upgrade

  1. Masonite Baffle

    Masonite Baffle

    1/4'' Masonite Baffle per Phil Thien's design. Inner diameter (240 degrees) is 2-1/4'' less than outer diameter (120 degrees). Outer diameter is slightly less than diameter of trashcan.
    • KC7CN
    • Media item
    • phil pre-separator thien upgrade
    • Comments: 0
    • Album: Dust Collector Pre-Separator Baffle Upgrade
  2. Separator Lid Upgrade

    Separator Lid Upgrade

    Phil Thien cyclone separator lid design upgrade.
    • KC7CN
    • Media item
    • phil pre-separator thien upgrade
    • Comments: 0
    • Album: Dust Collector Pre-Separator Baffle Upgrade
  3. ChrisMathes

    Thread Preview 'upgrade'

    (This is in regards to the 'preview' bubble that pops up on the title of a thread to show you the first couple lines of the discussion) I've just completed what I think will be seen as an 'upgrade' to the thread preview. This was initiated by a change request from mtrager and pappyj who wanted...
  4. SteveColes

    Photo Gallery Software Upgrade

    I've just completed upgrading our Photo Gallery software to the latest version. I have been waiting for this upgrade for a long time as it was supposed to have some features that I thought were important. Well as far as I can see, there isn't one new feature that we want.:slap::-(:-(Mad as...
  5. rick7938

    Miter Gauge Upgrade

    I am looking to upgrade the miter gauge on my Delta Contrator Saw. Various catalogs show new miter gauges from $50 for the basics to nearly $300 with many bells and whistles. My budget will only allow about $150 which will cover some of the mid-range Incra and Kreg miter gauges. What would you...
  6. Canuck

    Simple Upgrade!

    I decided this week that my Delta 14" bandsaw could do with a little maintenance. I replaced the stock tensioning spring with a "Cobra Coil" and the upper and low guide blocks with "Cool Blocks". Well let me just say that those two simple upgrades have made a world of difference for this saw...
    • Canuck
    • Thread
    • simple upgrade
    • Replies: 1
    • Forum: Reviews
  7. LeftyTom

    Upgrade Gloat

    I got tired of dragging the shop vac around, and the hose had gotten stiff with age (doesn't everything?). To go from 5' to 12' in length is an advantage alone. The old vac's tools will slip over the end of the new hose, but may be a tad loose in fit to be usable. No worries, the crevice tool...
  8. S

    upgrade your bandsaw

    .
  9. WoodWrangler

    Bandsaw Upgrade! Riser Block Installed

    This post is a little late, in relation to when I did it, but it's a GLOAT at any measure! My Grizzly bandsaw underwent a neck-lift with the riser block upgrade ... adding 6" cutting capacity! :eusa_danc The bad ... when I first installed it, I also put on a new blade. Not being that familiar...
  10. rhett

    grizzly 15" planer upgrade

    If anyone is or is planning to upgrade G0453 15" grizzly planer to a shelix head pm me. I have the three bearings, gasket and helical gear to do this correctly. I would rather throw these parts away than deal with Grizzly again. I will not get into why I have these parts, I will say though...
  11. rhett

    shop upgrade *pic*

    In order to cut full size sheet goods I must open my garage door, I only have 6' from front of saw to door. With my old door, when open, I only had 7' of headroom. Catch 22. Well, my problems have been solved. Got this door put in over the weekend with a high lift kit. Now I have all the...
  12. sapwood

    Uniped fence and mobile base upgrade

    Alas and at last I've completed upgrading my Grizzly tablesaw with a Unifence and mobile base. Couldn't resist a few pix and comments ;-) From the front: Decided to rename it the Uniped ;-) Retained the Griz backrail to attach the extension table. This made the wing more stable and allowed me...
  13. A

    More Tinkering- Drillpress upgrade *w/pics*

    My ongoing effort to upgrade some of my woodworking machines recently focused on my Delta 16 1/2" drillpress. My biggest complaint was changing speeds. Since I am a tinkerer I drill both wood and metal which require drastically different speeds. Changing belts was always a pain, especially if...
  14. sapwood

    Grizzly upgrade?

    As some of you already know I have a 1990 Grizzly 1023 tablesaw. With the help of fellow NCWWer the shaft and bearings have been replaced and the saw is running well. However, the fence needs replacing and the CI has some major dings. Currently I have a 30" Delta Unifence and rails back ordered...
  15. jmauldin

    table saw upgrade

    Well, I finally dod something I have been wanting to do for some time. The motor on my table saw was 110v, 1 1/2 hp. I have been wanting to upgrade, esp. since the motor was acting up (like all us old folks). Anyway, in addition to upgrading the motor I wanted to replace the on/off switch and...
  16. woodguy1975

    The Routertable Upgrade is Complete

    Nothing special, but the router table upgrade is complete. Some of you know I decided to upgrade my router/lift. I bought a PC 7518 router and the Bench Dog Prolift. Both are a very nice upgrade to my previous setup. I decided to paint the cabinet to match the cabinet of my Tablesaw. It is...
  17. b4man

    Old Jet band saw gets an upgrade

    A few weeks ago I decided to cut some brackets on my band saw. After I skinned my knuckles and wore a callus on my hand trying to tension the blade I started the saw and in about 10 seconds I smelled burning rubber. The sound wasn't quite right either. My first thought was the belt. On...
  18. SteveColes

    Software Upgrade on the horizon

    We currently run vbulletin ver 3.5.2. Jelsoft is getting ready to release 3.6. I will want to upgrade to it as soon as all the addons we use are ready and we have decided on a new(if we decide to do it) Photo Galley. This particular set of upgrades will be a bit harder to do than the last one...
  19. novice99

    Upgrade Fence or New TS

    as a relative newbie infected with the woodguy's disease, I am hungry to do more fine work (cabinetry, small boxes). I have an entry level TS which has served me well so far, other than all of the work to ensure that my fence is truly parallel to the blade. Any recommendations on upgrading my...
  20. A

    Unisaw upgrade underway w/*PICS*

    In addition to working on the assembly table I started the rework of my Unisaw mobile base and tables. After removing the Unifence rail, the extension table, and stock mobile base, I fabricated wheels and feet for my new mobile base. Here is the saw stripped of its extension tables, fence rail...

Premier Sponsor

Our Sponsors

LATEST FOR SALE LISTINGS

Top