handle

  1. K

    attaching a handle to a wooden mug

    Hello all, I've recently made a 6" tall mug which I would like to attach with a handle. I haven't fashioned the handle yet, because I have no idea how to attach it! I realize that a proper glue joint can be 'stronger than the wood itself', but simply gluing the handle to the mug surface...
  2. Jon

    I need a handle on this door

    I would like to get some suggestions on a flush mounted handle to put on my router table door. i could put just a cheapo Knob on it but I want it to be Flush with everything else on the side. Do you have any suggestions?
  3. Shaving Brushes

    Shaving Brushes

    Silver Tip Badger Hair Shaving Brushes. 25mm knot size (what holds the bristles and is embedded in the handle). The foreground one is Jarrah Burl, the middle is Cocobolo, and the far one is Brown Ebony.
    • Badabing
    • Media item
    • badger brush handle shaving turning
    • Comments: 0
    • Album: Turning
  4. B

    Door Handle Sets

    Folks, I am searching for some decent quality, contemporary door handles for interior doors (passage, privacy and dummy levers). I am having a hard time finding anything decent. Apparently there are no local sources, and even on the net I can't find anything decent. So far the only good...
  5. T

    Need a 5/8" x 11 tpi die and handle

    Help :help:, I need to borrow a 5/8" x 11tpi die and handle to tap 1 @ 3" piece of steel rod. Anyone in the area have one I could borrow? TIA
  6. CarvedTones

    adze handle too loose

    Or maybe I am pushing the limits again. I was just trying to make this little dent in this rock maple: And I am not sure you can tell in the blurry picture (sorry; grabbed one of my kids' cameras) but the head of my Stubai small sculpting adze is slipping off. It came off completely one...
  7. Splinter

    Spindle Gouge Handle

    Shortly after I got my lathe Mike Davis mailed me some old lathe chisels he had and a 3/8" spindle gouge (without a handle) that he made 20 years ago. I finally got a chance to make a handle for the gouge. It is made from Brazilian Mahogany, curly maple and walnut. The mahogany was actually...
  8. Sharp Blade

    Canarywood Handle just finished!

    I got bored yesterday and made a Canarywood handle for one of my planes. I used Danish Oil to finish it off. I am in LOOOOVVVEEE with Canarywood now!
  9. board and batten basement door

    board and batten basement door

    This handle was my pride and joy out of this door. It was cut out of oak from a scroll saw and then I routed the edges to round it out and make it friendlier to the hand.
    • OriginalChong
    • Media item
    • handle oak
    • Comments: 0
    • Album: board and batten door for my basement
  10. DaveO

    Box with HANDLE finished

    Well, I finished putting the shellac and lacquer finish on my Purpleheart and curly R.Oak box. I decided to go with the handle despite the jury being on the fence. I think it came out almost perfectly 50/50 in the hinge vs. handle inquiry. I did lower the height per several recommendations. The...
  11. DaveO

    To hinge or handle????

    Working on another box, and I would appreciate some guidance/direction. I am at an impasse as to whether this box should be hinged or get some funky handle and lift-off lid. It's unfinished Purpleheart and curly Red Oak. Advice and opinions desired. Thanks, Dave:-)
  12. C

    Handle for a pressure cooker

    My grandmother has a very old pressure cooker that has the handles broken off of them. She asked me to make her a new set out of wood for replacements. I have the 2 halves of one of the handles. My first thought was that wood wouldn't really do well as handles for the pressure cooker. My...
  13. mshel

    Emmert Vise w / handle

    Finished my vise handle today and had to post a pic of it with the vise and by itself. I made the main dowel part out of curly maple and the caps are a sandwich of mahogany and curly maple. I finished it with 3 wipe on coats of BLO and 1 wipe on coat of shellac. I really like the curl figure and...
  14. SteveColes

    Who did it and how did you handle it?

    In some thread, rcorne01 gave the classic answer of "seach" for it. Clay posted a linlink to the correct thread. Thank you. This morning rcorne01 post has either disappeared or was edited. I assume one of you did something. Thanks. How did you handle it and how did rcorne01 react. Learning...
  15. cloudancer

    looking for a handle

    3/8" racheting handles (I think its 16 tpi) in RTP? Normally Woodcraft carries them, but they are out when we were there last. I've tried Lowes, Home Despot, and Klingspor's Woodworking Shop. I can order it online, but it seems silly to pay $5 shipping for a $4 part. Unfortunatly the gas from...

Premier Sponsors

Contact for your financial processing needs!

Our Sponsors

LATEST FOR SALE LISTINGS

Top