video
-
Adding a short video clip to post
Hi Everyone, I have a short video clip that I would like to share with you all but I can't seem to figure out how to upload it into a post. It is of some very young ladies singing our National Anthem. If someone could help explain how to upload this or I can email it to you for uploading if that...- steviegwood
- Thread
- adding clip post short video
- Replies: 1
- Forum: Help Desk
-
Workbench Video Site
Sometime in the next month, or so, I plan to actually start working on the long overdue bench project for my shop. Looks like the project is going to be a bit involved, but long overdue. Anyhow ... In my "study" of this subject, I've so far read the Christopher Schwartz "Workbenches" book...- WoodWrangler
- Thread
- site video workbench
- Replies: 14
- Forum: General Woodworking
-
Frank Klausz cutting a mortise by hand video
When I went to the Woodworking in America Conference last November I brought along my little still camera. I began to take some videos with the little thing just because some of the presentations were so amazing. The quality is not the best, but the content is pretty good. Last night I was...- AAAndrew
- Thread
- cutting frank hand klausz mortise video
- Replies: 2
- Forum: User Announcements
-
Video Tour of Greene & Greene Inspired Home
http://woodtube.ning.com/video/greene-and-greene Some neat ideas for you G&G fans. Unfortunately, some of his creations are beyond the WAF (Wife Acceptance Factor) credits I have saved up w/Mary Ann.:wsmile:- Tarhead
- Thread
- greene home inspired tour video
- Replies: 3
- Forum: General Woodworking
-
Frank's 3 min. DT Video
http://popularwoodworking.com/klausz The also have pix of the new, Made in USA, UniSaw! pete- PeteM
- Thread
- frank min video
- Replies: 22
- Forum: General Woodworking
-
Need Video for PC 7116 omni JIG
Hey all, I have a copy of the instructional video for the Porter Cable 7116 Dovetail Omni Jig , however there is a bad spot on it. It only lasts for about 30-40 seconds but it is during that time that important setup instructions are demonstrated. Do:eusa_prayes anyone here know of where there...- skysharks
- Thread
- 7116 jig omni video
- Replies: 1
- Forum: Where Can I Find, Buy or Sell?
-
Video Review: 8 Point Rebuild/Basic Engine Building
Please take pity on me, I know this is a forum for wood. They do at one point, suggest using a wooden mallet if that counts? https://smartflix.com/store/video/504/8-Point-RebuildBasic-Engine-Building I post this only because its one of the bestest howto video's I've seen. Trust me, I've seen... -
Video Review: A Blacksmithing Primer....
Howdy all. As I now send a decent % of my paycheck to smartflix, thought I'd pass along some reviews to those who are going down the long dark road of howto video addiction! https://smartflix.com/store/video/2244/A-Blacksmithing-Primer This video set is long, 3 full dvd's worth. I... -
Video: Hand Tool TechniquesHand Tool Techniques: Precision Preparation of Chisels
Hand Tool Techniques: Precision Preparation of Chisels For Accurate Joinery ...with David Charlesworth DVD from Lie Nielson The highpoints, David Charlesworth continues with his approach he began in the outstanding 3 Hand Plane videos. He is very detailed, consistent and great at... -
Video Review: Drilling, Tapping and Milling on the Drill Press
Drilling, Tapping and Milling on the Drill Press ...with Rudy Kouhoupt Ok gang, if you are using a drill press, planning to use a drill press or even look sideways at a drill press..... This video answers almost any question you could have about the use of a drill press. He covers all... -
Testing Joints (video)
You may have seen this in the magazine, but here's a video of the test of various joints ... http://www.youtube.com/watch?v=DhLfb7m9Fug- WoodWrangler
- Thread
- joints testing video
- Replies: 1
- Forum: General Woodworking
-
T
Expanding table video?
Evening, Any of you folks seen the video on youtube of the expanding table? What an awesome project that must be? Any ideas as to how this was done? I had the link but cannot find it now. Always curious as to how things work! Tony ...- tonyps
- Thread
- table video
- Replies: 2
- Forum: General Woodworking
-
Wooden handplane setup video...
Hey for all you hand plane junkies, a nice and free video on setup and use of wooden hand planes from Knight Toolworks. http://www.knight-toolworks.com/Knight_Plane_Basics.rm Enjoy, Jim- froglips
- Thread
- handplane setup video wooden
- Replies: 1
- Forum: Hand Tools and their Use
-
Google Video for Woodworking Help
I'm sure some of you have already found this, but Google added videos to their search engine some time back. I've personally found this a great resource to find little tips & tricks about woodworking ... you should check it out sometime. Just go to Google.com, search for something, then click...- WoodWrangler
- Thread
- google video woodworking
- Replies: 6
- Forum: General Woodworking
-
Video: Forgotten Hand Tools, Christopher Schwarz
Howdy all you video dust mights! It gives me great pleasure to follow up my review of Coarse, Medium and Fine by Christopher Schwarz. This is the second video produced by Lie Nielsen. GET THIS DVD (and the other one). Don't dally. Do not pass go. In this video he goes into detail... -
Video Review: Coarse, Medium, Fine - Christopher Schwarz
Howdy Vid-ittes, Well, after finishing this fine fine video, wanted to fill in that missing 1/4". Heaping praise on Mr. Schwarz continues. One teaser, he answers the question "how in the world do you true the sole of a 22" jointer plane?". In addition to working on a flat panel, he... -
Site's First Video -Thanks to Steve D
We have created a new Photo Gallery Public Albums->Videos, and the video is there. Since we don't have streaming video capabilities, YET. Your only option is download the file and it is a big file, almost 700 MB. I want to thank Steve D for arranging this:eusa_clap- SteveColes
- Thread
- steve video
- Replies: 8
- Forum: Staff Announcements
-
Video Review: Tage Frid
Thought I'd pass along my comments on the new Tage Frid dvd. For those of you who enjoyed his older tape on making dovetails, this is a lot of fun. It covers a lot more about Tage Frid. Shows his home, some of the furniture he has made and lots of stories of his apprenticeship in Denmark...
Premier Sponsor
Our Sponsors
LATEST FOR SALE LISTINGS
-
-
-
-
-
SOLD -- $75: Gast moa v113 Vacuum Pump Veneer, 60" bag and board- Started by peterdnight
- Replies: 1