piece

  1. Tar Heel

    Need a small piece of plexiglass

    I need a piece of 1/4 inch plexiglass (3 1/2 X 30). The smallest piece Lowe's has cost $36 :BangHead: (I think it is 48 X 48). I'm building a crosscut sled and need it for the blade guard. Does anyone know of a place that will cut it in smaller pieces and not charge for the whole sheet?
  2. BKind2Anmls

    V-Belt Piece Needed

    I bought one of those red, linked, V-belts for my bandsaw but it was about 9" too short. I had a little piece left over from a couple of years ago when I replaced my table saw belt and added it. However, I am still short approximately 5 inches. Does anyone out there have a little piece of...
  3. cskipper

    "Nature's Majesty" - another challenging piece to cut

    Here are some pictures of the piece titled "Nature's Majesty". It is about 9" tall and 7".wide. I used PS #2 precision ground blades. I haven't sanded them (cut three) and won't until they are secured to a backing. The first two are from QS Sycamore: the next is a close up of the smaller...
  4. jonnyfontaine

    need piece cut with a tablesaw and tapering jig

    hi, i need to cut a piece of ebony (a fretboard for a guitar) with a slight taper on both sides with a table saw... the cut is really important so it needs to be very exact, the ebony is slotted for the frets already so it has 22 small kerfs in it... i've been told that to avoid chipping or any...
  5. Littlejon

    When A Piece Makes You Sad

    A few years ago my oldest son (now 10) noticed an elderly lady in our church had been using an old shoebox for a footstool on Sunday mornings because her feet didn't reach the floor. Well, he and several other boys sat with her every morning before going down to children's church and she had...
  6. U

    anyone who can power plane a 15"w piece of mahogany

    hi, i need to get a piece of mahogany that is 18"l x 15"w run through a planer... i am located in raleigh nc... please respond via e-mail to hotrodriot@hotmail.com... thanks much... jonny
  7. D

    ivey !?!? looking for an ash mantel piece and ...

    some hickory treads! ash mantel 6' long and maybe 4" thick and 10" wide! like a rough look(dull blade cut).:icon_thum 6 treads(hickory) 4' long 1" thick finished and 12 inch wide! :eusa_pray ivey?????
  8. Splinter

    Final Cut on turned piece??

    What is the proper or preferred method to cut the waste off the ends of a turned piece like the one in the attached photo?
  9. S

    6 Piece Multi Function Tool Kit: $5.98 @ Lowes

    .
  10. kota62

    1st real commisioned piece

    A good friend down the street asked for a TV stand to better match her older furniture, she gave me basic requirements but let me run with it... Solid cherry stained with red mahogany, then 2 coats of watco cherry danish oil. several coats of sprayed poly wet sanded to 600 grit, then several...
  11. skipwill

    Just down the road a piece....

    Hello all. Just down the road in Columbia, SC. I joined back when the NC Woodworker started, but never posted(three weddings in 2.5 years (all my daughters), retirement, grandkids, etc) and got removed:-( for inactivity. I'm back and hope to be more involved if i can ever get this house...
  12. adowden

    My first commission piece is done!

    I am so happy that I have FINALLY finished my first commission piece. It took much longer than I thought - 5 months part time (150 hours). It was quite a learning experience (Isn't this what you say when you way under quote the bid?:lol: ) It was alot of firsts for me - first inset doors...
  13. mshel

    Latest commission piece

    Made this night stand to go with the one a client brought me. Made of Walnut with secondary woods of maple, pine. Had to strip the original and finish them together and try to get them as close as possible. Might be off a little bit but the client was very pleased so guess it was close enough...
  14. SteveColes

    Any ideas of re-centering piece in chuck

    Once more I am trying to turn my first goblet.:yes4lo: Everything was going great:eusa_danc (I thought) I was hollowing the end grain to make the interior of cup portion, when suddenly the tenon slipped in the chuck. To make matters worse, it appears that it had slipped a bit even before, I...
  15. chris99z71

    My first commissioned piece

    So I was talking to one of the girls at work and mentioned that I'm into woodworking. I showed her the pictures of my bar and the cabinet that I made in John's class. She asked if I'd build her an end table. This is the one that she wants. She wants it slightly wider (26") and with two doors...
  16. mshel

    Latest commission piece

    Below are some quick pics of my latest commission piece. This is the companion piece to the hanging corner cupboard I built last month. Lots of hand work went into this little thing. The table stands 29"' high, top is 23 1/2" square. The queen ann legs were roughed out on the bandsaw, put in the...

Premier Sponsor

Our Sponsors

LATEST FOR SALE LISTINGS

Top