fix

  1. rifle_breakdown_20_

    rifle_breakdown_20_

    Early 19th century rebuild/restore piece
    • danmart77
    • Media item
    • cleaned fix patchbox piece pierced toe
    • Comments: 0
    • Album: Wayne Rifle Restoration
  2. Rip fence fix

    Rip fence fix

    Rip fence fix
    • MarkE
    • Media item
    • fence fix rip
    • Comments: 0
    • Album: Grizzly G0623X Assembly
  3. Rip fence fix

    Rip fence fix

    Rip fence fix
    • MarkE
    • Media item
    • fence fix rip
    • Comments: 0
    • Album: Grizzly G0623X Assembly
  4. Rip fence fix

    Rip fence fix

    Rip fence fix
    • MarkE
    • Media item
    • fence fix rip
    • Comments: 0
    • Album: Grizzly G0623X Assembly
  5. Rip fence fix

    Rip fence fix

    Rip fence fix
    • MarkE
    • Media item
    • fence fix rip
    • Comments: 0
    • Album: Grizzly G0623X Assembly
  6. Cato

    How to fix dye run??

    I have a dye run on a panel of a box and trying to figure out if I can fix it. I am using walnut, that I first sealed with a wash coat of shellac, then applied transtint orange with alcohol carrier, wiping it on. Well, I got a drip run on one side of the box that I didn't really notice until...
    • Cato
    • Thread
    • dye fix run
    • Replies: 5
    • Forum: Finishing
  7. JackLeg

    Grrr-Ripper Fix?

    I received the following reply from Micro Jig today. Guess we'll have to see if this works! :dontknow: Hi Reggie, Thank you for your support in our product - the GRR-Ripper® 3D Pushblock™ System. We are sorry that the Center Leg is being tight to adjust, this may cause by the contacting...
  8. R

    Can You Fix A Check?

    Is it possible to repair a check in the end of a really nice board? I realize that if a board has checked and the crack is 1/4" or wider, it would be pretty impossible. I have some wide boards that have checks in the end that have not really separated more than a 1/16" or less and I was...
    • robliles
    • Thread
    • check fix
    • Replies: 6
    • Forum: Wood
  9. Bas

    Chamfer accident - now how do I fix it?

    Don't you just love how a 5 second mistake can wipe out weeks of work? :BangHead: :BangHead: :BangHead: I'm building the "dancing clock" from some plans from Wood Magazine. The edges on the front of the body get a small chamfer (1/8"). Unfortunately, I also routed a chamfer on the face which I...
  10. Mr. Lahey

    Anyone know how to fix a cracked plastic auto lense?

    I have a orange turn signal light on a car that got busted, I glued it together the best I could but a few pieces are still missing from the plastic. Apparently the colored tape is not good enough for you to pass inspection, so now I just have clear duct tape over the remaining holes. Does...
  11. froglips

    Post Reported title fix.....

    Would it be helpful to the Mod's if I somehow tweaked the "Post Reported by <user>" to a more meaningful title? Maybe something like: PR: <Original Title> We can also control which forum the Post Reported is sent to. I could setup a "Post Reported" forum (how clever) and then tweak it so...
  12. C

    Uncovered pith Section - How to fix?

    I uncovered a section of pith when I cut the oval into my rectangular table top glueup. :eusa_doh: Here's a pic. The pith area is the round one near the center of the pic. The other light colored areas are just the rough edge from the jigsaw, I haven't shaved that area flat yet. I...
  13. Mark Gottesman

    Anyone ever fix a step pulley with JB Weld

    I am repairing a drill press that my father made while studying to be an Industrial Arts Teacher. So, I am trying to keep it "original", so to speak. Have a 4 step motor pulley that has a chip out of it. Has anyone ever tried to build up a missing section with JB weld and have it hold up in...
  14. CrealBilly

    How would you fix?

    I built this bed 8 years ago, before I had my sawmill and could saw my own lumber. It's is made out of 5/4 very low grade WO, that I bought from a local sawmiller. As you can see the lumber was not kiln dried but I did air dry it for a good year and 1/2 in my shop before I worked it into the...
  15. gordonmt

    Masonry fireplace fix

    I have a masonry fireplace and as most of you who have one, know that they can be very energy inefficient. In fact, when the outside temperature falls below 40f, a fire in the fireplace will actually pull conditioned warm air out of the house leaving you feeling cold. I found a solution I...
  16. T

    How do I fix bow in plywood drawer frame w/ pics?

    Much to my chagrin I have an 1/8" inch bow over a 26" span in the plywood frame for a bank of drawers in a dresser. The drawers are suppose to fit with a 1/6" clearance. Some how this happened although the case was perfectly square. I considered maybe wrapping with damp towels and clampping down...
  17. T

    How to fix this mistake? w/ pics

    I was routing tonight and had to 96 chamfer cuts on tongue and grove slats with m router station. I missed on one and really tore in to piece. Giventhe location of the board it will not be visible on the project (bed foot board against the box spring. Never the less I want to repair it the best...
  18. Bryan S

    To Fix or Adapt That is the Question

    Discovered another goof (this thread) with the entertainment center last night when glueing on the face frame. The bottem is about 1/16 wider than the middle and the top It's dificult to notice in the above pic but it is like this exagerated for clarity The problem is the bottem...
  19. froglips

    Loose drive drum in portable belt sander fix?

    I'm back, with yet another question..... I'm attempting to rebiuld/restore/six-million $ man my old craftsman 3x21 portable belt sander. All parts are off, accept for the drive drum in the back end of the sander. As best as I can tell, its a gear press fit on a shaft that has the drum...
  20. skysharks

    Finally Got a fix for my Bandsaw

    Hey all If you would remember back to my problem with the Carter Bearings upgrade to my Grizzly Band saw. http://www.ncwoodworker.net/forums/showthread.php?t=10412 Well after a dozen or so emails with pics and phone conversations with Carter techs, I took the ball back into my court. These...

Premier Sponsor

Our Sponsors

LATEST FOR SALE LISTINGS

Top