sled

  1. BKHam

    cool way to dress up / complicate a plywood bookcase

    i started out naively thinking that it would be a quick 45 miter, then i was thinking it will be a 30 / 60 degree combo. then i realized its something altogether different. I used a easy 2x2 square to try and figure out the two angles involved. I had a unfinished table saw sled i cannibalized...
  2. W

    First of 2 questions about crosscutting

    Early in my woodworking "career" I built a crosscut sled that has been used extensively. Recently, I purchased a used Incra Miter 5000 which has been used little. I am thinking of replacing my crosscut sled with a newer more accurate one. My question is whether the Miter 5000 replaces a shop...
  3. photo7

    photo7

    • harvey314
    • Media item
    • attachment jawhorse rockwell router sled
    • Comments: 1
    • Album: Router sled 1
  4. photo6

    photo6

    • harvey314
    • Media item
    • attachment jawhorse rockwell router sled
    • Comments: 0
    • Album: Router sled 1
  5. photo5

    photo5

    • harvey314
    • Media item
    • attachment jawhorse rockwell router sled
    • Comments: 1
    • Album: Router sled 1
  6. photo4

    photo4

    • harvey314
    • Media item
    • attachment jawhorse rockwell router sled
    • Comments: 0
    • Album: Router sled 1
  7. photo3

    photo3

    • harvey314
    • Media item
    • attachment jawhorse rockwell router sled
    • Comments: 0
    • Album: Router sled 1
  8. photo2

    photo2

    • harvey314
    • Media item
    • attachment jawhorse rockwell router sled
    • Comments: 1
    • Album: Router sled 1
  9. BS Small Parts X-Cut Sled

    BS Small Parts X-Cut Sled

    Great for pen blnks and other small pieces
    • Canuck
    • Media item
    • bs parts sled small x-cut
    • Comments: 0
    • Album: Shop Stuff
  10. BS Small Parts X-Cut Sled

    BS Small Parts X-Cut Sled

    Great for pen blnks and other small pieces
    • Canuck
    • Media item
    • bs parts sled small x-cut
    • Comments: 0
    • Album: Shop Stuff
  11. BS Small Parts X-Cut Sled

    BS Small Parts X-Cut Sled

    Great for pen blnks and other small pieces
    • Canuck
    • Media item
    • bs parts sled small x-cut
    • Comments: 0
    • Album: Shop Stuff
  12. H

    Miter sled

    Can anyone recommend a site for building a miter sled, for cutting segments on a table saw? Thanks.
  13. Rhythm House Drums

    Angled Rip Sled

    I do a lot of tapered rips on my table saw. I'm using a metal taper jig... it's horrible. I have to cut blocks to fit inside the jig or-else it will bend a bit when cutting. Took me a few curved cuts to figure out what was going on. I was hoping the Incra Miter 5000 would do rip cuts...
  14. Bigdog72

    Panel Cutting Sled

    I need to make a panel cutting sled and, although I know it's easy to make, I am not sure on dimensions. So....post pictures, post details or share plans.....Please!!
  15. bluedawg76

    new planer sled

    after spending a couple of nights face jointing boards by hand that were too big for my 6" jointer, i decided to re-enter the 21st century and build a planer sled. Build is a rather loose term as this is about the simplest jig I've made. There's lots of versions I found online that I used as...
  16. Steve_Honeycutt

    Table Saw Cross Cut Sled

    I am thinking of building a cross cut sled for my table saw. I plan to make it from 3/4 plywood that I have left over from previous projects. What are some helpful features of a good cross cut sled? Thanks Steve
  17. Y

    cross cut sled

    I want to build a cross cut sled for my table saw.I'm concerned about getting it perfectly square with the blade. Any tips?
  18. zapdafish

    nice cross cut sled plans

    http://americanwoodworker.com/blogs/shop/archive/2009/08/12/improved-crosscut-sled.aspx I built this over the weekend and its probably the most usefull jig I could have made for my TS. I was using an incra miter gauge but switch angles on it and getting back to 90 deg cuts is a pain. I like...
  19. M

    Need a solution for loose table saw sled runner

    I have a specialty, homemade crosscut table saw sled with a slightly sloppy wooden runner. Seems the wooden runner dried and shrank a bit and now I get a little wobble. Anyone know of a solution for this? The runner is not easily replaced, as it is epoxied onto the sled!:help:
  20. 100_2131

    100_2131

    • Canuck
    • Media item
    • crosscut sled universal
    • Comments: 0
    • Album: Shop Stuff

Premier Sponsors

Contact for your financial processing needs!

Our Sponsors

LATEST FOR SALE LISTINGS

Top