request

  1. CarvedTones

    Name change request

    I have been back and forth on this, but I finally decided that I should go ahead and switch to "CarvedTones" if that is easily doable. I am getting a little more serious about getting that part time venture off the ground, so I am laying claim to the ID (I own the domain, registered the eBay...
  2. Bas

    Name change request from Onobeano

    This was sent to webmaster@ncwoodworker.net. I'll take care of it. Hi, My current username is Onobeano, a name I am well-known by in the coffee industry (from my e-business CoffeeBeanCorral, which I sold last year). I would like to change it to my real name to be in better compliance with...
  3. froglips

    Feedback: Request to change some site colors....

    We have had a good "complaint" about some background colors being hard to read. The thread is here:http://www.ncwoodworker.net/forums/showpost.php?p=242308&postcount=1 Here is where I came to understand the issue. http://www.ncwoodworker.net/forums/showpost.php?p=242659&postcount=9...
  4. HMH

    PE Request: Huntersville to Raleigh area

    Hey Folks, I "impulsively" bought an old Walker Turner bench top lathe off of EBAY a few weeks back, and I really need to get it out of the sellers garage in Huntersville. I was actually on business in the Matthews/ Ballantyne area on Friday, and I had intended to pick it up then, but one of...
  5. Mark Stewart

    Help request for a new turner.

    Well I have done a bit of turning over the last year or so on my pencile lathe and I need some help. Is there any one who lives close that can give me some guidance on chisle sharpening. I seem clueless. I love to turn but I do need a lesson or two. Thanks Mark:embarrassed:
  6. S

    Porch Floor Advice Request

    Hi, I'm new here but you guys seem to have a lot of good information. I need to replace the floor of my covered front porch. The original, built in 1924, is 5/4 X 3" tongue and groove. I don't know the wood...maybe fir or pine. The porch is 30' wide and 8' deep. In appearance, I would like...
  7. WoodWrangler

    Request for Lathe Bed Gap Measurements

    Calling all mid- and full-size lathe owners! I need your help :help: Can you reply in this thread with the make/model of your lathe and the measurement of the gap/space in your lathe bed (see image)? Be as accurate as your tools will allow, but machinist accuracy is not required. Reported...
  8. S

    Charlotte to Cary _ PE Request

    Set of (4) Great Lakes casters need to roll from Charlotte(Woodwrangler) to Cary(Splint Eastwood), preferably by motorized vehicle:gar-Bi also with brakes! Much Thanks in Advanced! Matt
  9. S

    prayer request

    .
  10. CrealBilly

    New Forum Request

    Was wondering if we could have a gardening forum? - alot of us WWers are into gardening and I don't see how tips on ras'in maters and the like could be all that confrontational - but I could be wrong... you never know with Reggie hanging around :gar-La;.
  11. gfernandez

    Pony Express Request -Asheville or Hickory to Raleigh/Durham

    Looking to see if anyone was available to bring a router table from Asheville or Hickory to Raleigh/Durham/Burlington area any time soon. I'd be grateful for any help. Please PM or leave a reply for more info. Gonzalo
  12. J

    Pony Express request from Berea NC to New Hill NC

    Need to move about 4000 ~ 5000 BF of oak lumber from Berea to New Hill. Lumber is green and a little over 8' long, estimated weight is 20800 ~ 26000 lbs (10 ~ 13 tons). A 8 x 24' tandem axle flat bed truck would work out nice that would make up 6 4' wide dead stacked bunks on the bed. Other...
  13. John Reeves

    Opinion request, router in table saw

    I think I want to mount a router in my table saw. I would appreciate advice and guidance in at least two subjects. 1) Which router; a) Freud 2000E, a 3 1/4 hp 15 amp plunge router, 13 lbs but no height control from the top b) Craftsmen 2 1/5 hp, 12 amp 9 lbs. comes with two bases and does have...
  14. mkepke

    Request for assistance - machining pvc fittings

    I need to make a custom male-male pvc union. To do that, I need to machine the stubs on two stock plumbing unions so they fit inside each other. Reduce the OD on one fitting and increase the ID on the other fitting so that they mate for gluing. Is there someone out there with a machine lathe...
  15. PeteM

    Request for NCWW Pony Express help

    I need to get a Jet DC from Ron (yellowfin) in Fuquay-Varina to Charlotte. Ron is currently in Germany and will be back Saturday night. Any help would be greatly appreciated. TIA - pete
  16. ACobra289

    Request for Winston-Salem area members

    Hello all. Sometime within the next month or two or three I will be installing some hardwood floors in my house. I am going to need a moisture meter to check the wood and the underlayment to make sure they are within specs. If possible I would like to borrow a meter from a fellow member. If you...
  17. gazzer

    Lathe help request on Craiglist

    Saw this request for assistance in setting up a lathe on Craigslist. http://raleigh.craigslist.org/tls/522985123.html
  18. sapwood

    DQ Exception Request

    4Yanks posted he is heading overseas again and was concerned about his DQ status. Is there a way for us to "fudge" his numbers or status? I think his situation merits an exemption from the normal requirements. And, of course, he may have occasional opportunities to log on while there. Roger
  19. sapwood

    Leave Request

    I'm abandoning my duties and heading to the coast for a few days. I'll be gone from afternoon of 10/4 through 10/8 or so. It's our sixth Outer Banks volleyball trip, appropriately dubbed OBX Volleyball Invitational VI. We only have two rules: If it's inside the line it counts and bring your...
  20. adowden

    Request for custom mantle

    A gentleman in Chapel Hill contacted me earlier this week about wanting a custom fireplace mantle. I have too many current projects and an unfinished workshop. If anyone is interested, you can send me a PM.

Premier Sponsor

Our Sponsors

LATEST FOR SALE LISTINGS

Top