door

  1. KC - 15 Doors in a Frame

    KC - 15 Doors in a Frame

    An assemble pair of doors mounted in a bulletin board frame. Note the tempered hardboard in the center of the frame.
    • McRabbet
    • Media item
    • board bulletin door kellogg
    • Comments: 0
    • Album: Outdoor Bulletin Boards
  2. Jon

    I need a handle on this door

    I would like to get some suggestions on a flush mounted handle to put on my router table door. i could put just a cheapo Knob on it but I want it to be Flush with everything else on the side. Do you have any suggestions?
  3. KC Doors - 09

    KC Doors - 09

    Door frames are 3'' White Oak with McRabbet joint secured with 2'' #8 screws. 3/16'' tempered hardboard set in a centered 1/4'' groove on the inside provide substrate for 1/4'' cork sheet and insures square frame. Door fits inside frame.
    • McRabbet
    • Media item
    • board bulletin door kellogg
    • Comments: 0
    • Album: Outdoor Bulletin Boards
  4. KC Doors - 08

    KC Doors - 08

    They are large doors -- each measures 43'' x 39'' and will be hung using piano hinge along one side
    • McRabbet
    • Media item
    • board bulletin door kellogg
    • Comments: 0
    • Album: Outdoor Bulletin Boards
  5. KC Doors - 07

    KC Doors - 07

    and excess glue wiped off to yield a strong corner
    • McRabbet
    • Media item
    • board bulletin door kellogg
    • Comments: 0
    • Album: Outdoor Bulletin Boards
  6. KC Doors - 06

    KC Doors - 06

    Pegs driven home
    • McRabbet
    • Media item
    • board bulletin door kellogg
    • Comments: 0
    • Album: Outdoor Bulletin Boards
  7. KC Door - 03

    KC Door - 03

    Drilling Peg Holes with 3/8'' Forstner Bit
    • McRabbet
    • Media item
    • board bulletin door kellogg
    • Comments: 0
    • Album: Outdoor Bulletin Boards
  8. KC Door - 05

    KC Door - 05

    3/4'' long Oak pegs inserted with TB II
    • McRabbet
    • Media item
    • board bulletin door kellogg
    • Comments: 0
    • Album: Outdoor Bulletin Boards
  9. KC Door - 04

    KC Door - 04

    Jig is a half lap in a scrap piece -- holes oriented to avoid brads from opposite side that secure corner glue-up.
    • McRabbet
    • Media item
    • board bulletin door kellogg
    • Comments: 0
    • Album: Outdoor Bulletin Boards
  10. KC Door - 02

    KC Door - 02

    Jig for drilling 3/8'' peg holes
    • McRabbet
    • Media item
    • board bulletin door kellogg
    • Comments: 0
    • Album: Outdoor Bulletin Boards
  11. KC Door - 01

    KC Door - 01

    Bulletin Board Door - 43'' x 39'' Lexan in a 2'' White Oak frame. Corners half-lapped, but need extra strength.
    • McRabbet
    • Media item
    • board bulletin door kellogg
    • Comments: 0
    • Album: Outdoor Bulletin Boards
  12. B

    Source for door skins

    I am refinishing some interior slab doors. Some of the doors need to build up slightly to consistent thickness. So, where can I find door skins in or near Durham? I like to get the thin 'stuff' about 3/32 or so thickness. Any hint, tip, advice is appreciated! Cheers, Bernhard
  13. nelsone

    Garage Door Repairs

    I need to replace the lower panel on my garage door. I'm thinking on using douglas fir for the frames and was wondering if you guys had any other suggestions. Also any recommendations on where to get the material would be great! I've checked with Queen City Lumber and HS Lumber and douglas fir...
  14. K

    door size question

    I am making two vanties similar in style of an old fashion wash stand. Will use vessels ( sinks) sitting on top. To keep the style as close as possible to wash stands I am going to place two drawers at the bottom of the carcass. Normally the drawer would be at the top but this is not possible...
  15. goodmund

    Kitchen Cabinet Door Question

    I could use the opinion of the masses here: I'm in the process of putting together about 60 cope and stick doors and drawer fronts for my kitchen. All the panels are 1/4" G2S veneer core maple plywood and will get a clear finish to match the hard maple frames. When it comes to cutting the...
  16. B

    Door Handle Sets

    Folks, I am searching for some decent quality, contemporary door handles for interior doors (passage, privacy and dummy levers). I am having a hard time finding anything decent. Apparently there are no local sources, and even on the net I can't find anything decent. So far the only good...
  17. Glennbear

    cabinet door question

    Just under a year ago I purchased my new home. The kitchen has oak cabinets with the typical panel/ stile doors. These cabinets were produced in a production shop back in 2006 and apparently spaceballs or a similar preventitive measure were not used when doors were assembled. With the house...
  18. J

    Corner cupboard progress--bottom door

    I am making slow but sure progress on my corner cupboard. I am still working on the bottom cabinet; specifically, assembling the doors. I am trimming the tenons on the rail pieces to fit into the mortices on the stiles. I just raise the bench dogs about 1/4" and clamp the rail between them while...
  19. Tar Heel

    Who has made a post office box door bank? I need.....

    I have two post office box doors that I am going to use to build a bank for each of my grand kids. Does anyone know where I can order the brass coin slots? Thanks.
  20. LeftyTom

    Where 2 Buy Mirror for Door?

    What is your source for mirror(s) to go inside doors of a cabinet, armoire, etc? Do you have a source for mirror cut to size? Or do you pick up a mirror slightly larger than you need, and size it with a glass cutter and straight edge?

Premier Sponsor

Our Sponsors

LATEST FOR SALE LISTINGS

Top