raised
-
Pre-Finishing Raised Panels
Well. I have managed to complete 8 raised panel doors (dry fitted). Thread - http://www.ncwoodworker.net/forums/showthread.php?t=10958 I believe that I read somewhere that one should prefinish the panels prior to glueup in order to account for wood movement and an unsightly edge as the panels...- Canuck
- Thread
- panels prefinishing raised
- Replies: 5
- Forum: General Woodworking
-
T
Raised Panel Doors; how flat for the panel?
Please see the pictures below. I milled these panels (9 1/4" x 33") and had them flat and neatly stacked on my tablesaw. Went out of town for a week and came back to find them warped. :BangHead: Is this amount of cup/twist OK? Should I cut them down the middle, glue clamp and mill again? Does...- Travis
- Thread
- doors flat panel raised
- Replies: 4
- Forum: General Woodworking
-
Making raised panel cabinet doors ?
I ordered the 6 piece set Is there anything else I should know or order for makingg Doors? Ive never done any. Is there a How to on making doors ? I really appreciate any advice you guys or gals could offer.- Jon
- Thread
- cabinet doors making panel raised
- Replies: 11
- Forum: General Woodworking
-
C
Raised Panel Bit Set
I spent 6 hours Saturday and 7 hours yesterday fiddling with my no-name 3 piece raised panel set to make two panels. I re-made 2 sets of stiles while trying to get rid of the gap between stiles and rails that was visible on the face. I learned a lot but ended up ripping a few thousandths off...- cpowell
- Thread
- bit panel raised set
- Replies: 29
- Forum: General Woodworking
-
Free Hand Router Sign - Raised Letters
These are my first "non-test" Free Hand Routed Raised Letter signs. I did them with a $9.99 1/4" Trim Router using a 12" x 12" plexi base (see Misc album for photo). They are 24" x 16" and will be mounted back to back between two 4x4 posts. I still have a lot of practice to get good but I am...- Splinter
- Thread
- free hand letters raised router sign
- Replies: 11
- Forum: General Woodworking
-
Raised Letter Sign..Need Advise
I want to make a raised letter sign to use in front of my house and I need some advise from someone that has made them. I will be using a DW621 router and thought I would use a 1/4" collet. I did a little testing today. I used a 1/8" spiral bit to cut around the letters that I had marked on the...- Splinter
- Thread
- advise letter raised signneed
- Replies: 1
- Forum: General Woodworking
-
Raised panel detail from computer desk
Eight foot tall computer desk (desk + hutch). Birch, birch ply and ziricote pegging.- mkepke
- Media item
- panel raised
- Comments: 0
- Category: Member Galleries
-
D
How do I make slightly curved raised panel doors?
Anybody ever successfully try this..... If so, how did you do it? I got asked to consider making a credenza that would be about 10' wide, 36" high and have a CURVED :roll: front on it. In the middle the radius would extend forward about 12" further than the left/right of the cabinet. This is...- DaveD
- Thread
- curved doors make panel raised slightly
- Replies: 9
- Forum: General Woodworking
-
Raised panels for TV cabinet
TV cabinet side panel glued up and ready to be cut to length.- D L Ames
- Media item
- and panel rail raised stile
- Comments: 0
- Album: Corner TV Cabinet
-
Raised panels for TV cabinet
TV cabinet side panel glued up and ready to be cut to length.- D L Ames
- Media item
- and panel rail raised stile
- Comments: 0
- Album: Corner TV Cabinet
-
Raised panel for TV cabinet
Raised panel profile.- D L Ames
- Media item
- and panel rail raised stile
- Comments: 0
- Album: Corner TV Cabinet
-
Raised panel for TV cabinet
Raised panel for TV cabinet.- D L Ames
- Media item
- and panel rail raised stile
- Comments: 0
- Album: Corner TV Cabinet
-
Rail & Stile Profile fot TV Cabinet
Rail and stile profile.- D L Ames
- Media item
- & panel rail raised stile
- Comments: 0
- Album: Corner TV Cabinet
-
Rail & Stile Profile fot TV Cabinet
Rail and stile profile.- D L Ames
- Media item
- & panel rail raised stile
- Comments: 0
- Album: Corner TV Cabinet
-
Rail & Stile Profile fot TV Cabinet
Rail and stile joint offers a fair amount of glueing surface.- D L Ames
- Media item
- & panel rail raised stile
- Comments: 0
- Album: Corner TV Cabinet
-
Rail & Stile Profile fot TV Cabinet
Rail and stile for TV cabinet prior to glue up. I am using Space Balls to help maintain panel alignment.- D L Ames
- Media item
- & panel rail raised stile
- Comments: 0
- Album: Corner TV Cabinet
-
Rail & Stile Profile fot TV Cabinet
Shot of rail and stile prior to glue up.- D L Ames
- Media item
- & panel rail raised stile
- Comments: 0
- Album: Corner TV Cabinet
-
Veneered raised panels
Has anybody ever veneered the field of a raised panel before? I may get a job building a walnut bookcase with raised panel doors, and I was thinking of making the panels really stand out. Of course, I gravitated to burled walnut or something along those lines, which pretty much means veneer...- Wes
- Thread
- panels raised veneered
- Replies: 5
- Forum: General Woodworking
-
Raised panel doors
LOML finished the upper kitchen cabinet doors. They are beautiful (yes, I am biased but they really are awesome!). Here are some pictures: The unfinished wall will have another cabinet and tiled back board between it and the upper cabinet. John did a terrific job on these cabinets but...- cskipper
- Thread
- doors panel raised
- Replies: 21
- Forum: General Woodworking
