dowel

Doweled drawers
- Bas
- Media item
- Oct 4, 2011
- dowel drawer
- Comments: 0
- Album: New workshop
Doweled drawers
- Bas
- Media item
- Oct 4, 2011
- dowel drawer
- Comments: 0
- Album: New workshop
Doweled drawers
- Bas
- Media item
- Oct 4, 2011
- dowel drawer
- Comments: 0
- Album: New workshop
Doweled drawers
- Bas
- Media item
- Oct 4, 2011
- dowel drawer
- Comments: 0
- Album: New workshop
Doweled drawers
- Bas
- Media item
- Oct 4, 2011
- dowel drawer
- Comments: 0
- Album: New workshop
Doweled drawers
- Bas
- Media item
- Oct 4, 2011
- dowel drawer
- Comments: 0
- Album: New workshop
Doweled drawers
- Bas
- Media item
- Oct 4, 2011
- dowel drawer
- Comments: 0
- Album: New workshop
S
Looking for Dowel Max or Joint Genie

I'm looking for either a Dowel Max or Joint Genie. Anyone out there interested in selling theirs? Please reply with personal email. Thanks, Scott C Saluda, NC
- Scott Cardais
- Thread
- Feb 2, 2010
- dowel genie joint max
- Replies: 0
- Forum: Where Can I Find, Buy or Sell?
Peachtree Dowel Jig $25.79

The ad doesn't state that it is self centering, I called and they verified it is. http://www.ptreeusa.com/edirect_110609.htm
- Ken Massingale
- Thread
- Nov 6, 2009
- $2579 dowel jig peachtree
- Replies: 0
- Forum: Found for Sale/Hot Deals
Tenon on a Dowel ?

I am currently working a project that calls for turning a 1/2"D by 1/2" long tenon on the ends of a piece of 3/4" dowel. My question is how to mount about an 8" piece of 3/4" oak dowel between centers on my lathe?:icon_scra Can I capture one end of the dowel stock at the headstock with my...
- Canuck
- Thread
- Oct 13, 2009
- dowel tenon
- Replies: 12
- Forum: Woodturning
Dowel question

I hope I am in the right forum for this - and I hope that I can explain it good enough for you to understand - I am working on a project - I can not reveal what it is - surprise - I need to fix a piece of wood that will have a dowel running through it - the piece needs to swing in and out on the...
- PChristy
- Thread
- Feb 1, 2009
- dowel question
- Replies: 9
- Forum: General Woodworking
Dowel-Pro or Use Dowel Centers?

I got a Dowel-Pro last week, and tried my hand at it last night. I can get the holes to line up, and the joint areas are tight and clean. But the holes are not always centered in the edge of the wood, because the Dowel-Pro has three hole sizes (1/4", 5/16", and 3/8"), and guidelines for which...
- LeftyTom
- Thread
- Feb 27, 2008
- centers dowel dowelpro
- Replies: 7
- Forum: General Woodworking
base for Lie-Nielsen dowel plate

Design is copied from similar base made by Bill Anderson. Base is designed to be held in a bench vice and enabling someone to drive dowels through to cut them to indicated size. The rationale for this is commercially available dowels are often not accurately sized. This makes it...
- jglord
- Media item
- May 14, 2007
- dowel lie-nielsen plate
- Comments: 0
- Album: General woodworking
Miller Dowel System. Your thoughts

I would appreciate your thoughts on these, if you have used them how did you like them. I have been thinking about trying thes for some time and they look like their easy to use and seams to add a nice touch. Details for Miller Dowel System - Rockler Woodworking Tools Rockler still had a...
- Bryan S
- Thread
- Jan 5, 2007
- dowel miller system thoughts
- Replies: 5
- Forum: General Woodworking
How to put a sharp point on a dowel?

I don't have a lathe, but figure there has to another method for putting a reasonably sharp point on the end of a 1" hardwood dowel, so it can be driven into the ground easily. You know, like a pencil sharpener! Sander takes too long. Can it be done with a TS, BS, DP, router (not in table)...
- sapwood
- Thread
- Jun 12, 2006
- dowel point put sharp
- Replies: 12
- Forum: General Woodworking