kellogg
-
CL: 1830's Antique J. Kellogg All Boxwood Plow Plane
This is a rare thing to find on Craigslist ... expensive, but rare. http://charlotte.craigslist.org/tls/971931428.html 1830's Antique J. Kellogg All Boxwood Plow Plane - $450 (Shelby, NC) Reply to: sale-971931428@craigslist.org [?] Date: 2008-12-28, 10:36AM EST For sale is a J. Kellogg...- WoodWrangler
- Thread
- 1830 antique boxwood kellogg plane plow
- Replies: 2
- Forum: Found for Sale/Hot Deals
-
KC - 24 Angles and half-laps
A parting look at the main posts with half-lapped horizontal 4x4's for the door opening and roof framing. The diagonals were half-lapped onto the roof frame (see KC - 20) and lag screwed into the main posts.- McRabbet
- Media item
- board bulletin completion kellogg
- Comments: 0
- Album: Outdoor Bulletin Boards
-
KC - 23 A Close Up
Here's a closer look at the doors after installation. I caulked all around the White Oak frame with clear silicone door and window caulk.- McRabbet
- Media item
- board bulletin completion kellogg
- Comments: 0
- Album: Outdoor Bulletin Boards
-
KC - 22 Craft Center Kiosk
Here is the kiosk at the beginning of the trail at the Craft Center building.- McRabbet
- Media item
- board bulletin completion kellogg
- Comments: 0
- Album: Outdoor Bulletin Boards
-
KC - 21 Testing the Doors
Yep -- they even open and close! I installed some simple knobs to facilitate access when doors are opened for posting information.- McRabbet
- Media item
- board bulletin installation kellogg
- Comments: 0
- Album: Outdoor Bulletin Boards
-
KC - 20 Finishing the Job
The center post was installed and the frames installed -- clearance was less that 1/8" and they actually fit! Because of some minor warping in the PT wood, I used construction shims to insure the frames stayed square as they were locked in with 3'' deck screws.- McRabbet
- Media item
- board bulletin installation kellogg
- Comments: 0
- Album: Outdoor Bulletin Boards
-
KC - 19 Final Roofing
Next, 30-year fiberglass reinforced architectural tab shingles were installed with a matching roof shingle cap. Ready for the bulletin board frames with their doors.- McRabbet
- Media item
- board bulletin installation kellogg
- Comments: 0
- Album: Outdoor Bulletin Boards
-
KC - 18 Roof Installation
A ten-foot ridge board was dropped into a slot in the 6x6 post tops and 2x4 rafters cut with seats to fit on top of the rectangular frame shown in KC - 17. Then I installed 1/2'' PT plywwod sheathing and 30# tar paper.- McRabbet
- Media item
- board bulletin installation kellogg
- Comments: 0
- Album: Outdoor Bulletin Boards
-
KC - 17 Stage Two of Installation
Next, the roof support frame and diagonals were installed -- all in 4x4 PT material. Center upright will separate the door/frame sets.- McRabbet
- Media item
- board bulletin installation kellogg
- Comments: 0
- Album: Outdoor Bulletin Boards
-
KC - 16 Starting the Installation
The first step to install the kiosks was to dig the holes (2-man auger), drop the 6x6 posts into the two holes and clamp the two horizontal half-lapped beams in place to form the Bulletin Board openings -- the diagonal bracing insured these opening were square and braces to ground maintained...- McRabbet
- Media item
- board bulletin installation kellogg
- Comments: 0
- Album: Outdoor Bulletin Boards
-
KC - 11 Finishing the Hinge Mortise
Note the Edge guide is utside the frame and 1/4'' bit is inside -- this means a hard-to-control ''climb cut'' for that last inch or so. Obviously, I'd have been better off cutting these mortises before the frames were assembled, but I pulled it off with only one minor slip that cut into the...- McRabbet
- Media item
- board bulletin door kellogg
- Comments: 0
- Album: Outdoor Bulletin Boards
-
KC - 10 Hinge Mortise
Starting the Hinge Mortise -- 1/4'' bit with edge guide, but it falls an inch short -- a challenging climb cut is needed -- see KC - 11- McRabbet
- Media item
- board bulletin door kellogg
- Comments: 0
- Album: Outdoor Bulletin Boards
-
KC - 14 Installing the Hinges
17 screws per frame plus 17 in each door times eight doors -- that's a bunch of pilot holes and screwing!- McRabbet
- Media item
- board bulletin door kellogg
- Comments: 0
- Album: Outdoor Bulletin Boards
-
KC - 13 Hinge in the Mortise
The Mortise accepts the hinge perfectly.- McRabbet
- Media item
- board bulletin door kellogg
- Comments: 0
- Album: Outdoor Bulletin Boards
-
KC - 12 Hinge Ready to Install
Once the hinge mortises were cut and the hinge mounted on the door, we are ready to install them in the frame -- note the spacer under door to keep door at correct height.- McRabbet
- Media item
- board bulletin door kellogg
- Comments: 0
- Album: Outdoor Bulletin Boards
-
KC - 15 Doors in a Frame
An assemble pair of doors mounted in a bulletin board frame. Note the tempered hardboard in the center of the frame.- McRabbet
- Media item
- board bulletin door kellogg
- Comments: 0
- Album: Outdoor Bulletin Boards
-
KC Doors - 09
Door frames are 3'' White Oak with McRabbet joint secured with 2'' #8 screws. 3/16'' tempered hardboard set in a centered 1/4'' groove on the inside provide substrate for 1/4'' cork sheet and insures square frame. Door fits inside frame.- McRabbet
- Media item
- board bulletin door kellogg
- Comments: 0
- Album: Outdoor Bulletin Boards
-
KC Doors - 08
They are large doors -- each measures 43'' x 39'' and will be hung using piano hinge along one side- McRabbet
- Media item
- board bulletin door kellogg
- Comments: 0
- Album: Outdoor Bulletin Boards
-
KC Doors - 07
and excess glue wiped off to yield a strong corner- McRabbet
- Media item
- board bulletin door kellogg
- Comments: 0
- Album: Outdoor Bulletin Boards
-
KC Doors - 06
Pegs driven home- McRabbet
- Media item
- board bulletin door kellogg
- Comments: 0
- Album: Outdoor Bulletin Boards
