clamp
-
EndVice-bottom
- merrill77
- Media item
- clamp end pipe vice
- Comments: 0
- Album: Workbench build
-
Workbench build - face vice
This block on the face of the rear pipe clamp engages with the slot on the benchtop to resist twisting of the pipe clamp and support the pipe clamp when fully extended- merrill77
- Media item
- clamp pipe vice workbench
- Comments: 0
- Album: Workbench build
-
Workbench build - face vice
In the fully extended position- merrill77
- Media item
- clamp pipe vice workbench
- Comments: 0
- Album: Workbench build
-
Workbench build - face vice
Fitted wooden blocks and screws serve as a latch to hold the face to the pipe clamp face.- merrill77
- Media item
- clamp pipe vice workbench
- Comments: 0
- Album: Workbench build
-
Workbench build - face vice
View of the pipe clamps from the bottom of the bench- merrill77
- Media item
- clamp pipe vice workbench
- Comments: 0
- Album: Workbench build
-
Workbench build - face vice
Two UHMW strips are inserted into each hole to conteract the tendency of the vice face block to tilt back on the pipe. You can see one strip at the bottom of the holes on the inside face. There is an additional strip on the top of the outside face. The pair tilts the face block forward slightly...- merrill77
- Media item
- clamp pipe vice workbench
- Comments: 0
- Album: Workbench build
-
Face vice built with pipe clamps
- merrill77
- Media item
- clamp face pipe vice
- Comments: 0
- Album: Workbench build
-
Face vice built with pipe clamps
- merrill77
- Media item
- clamp face pipe vice
- Comments: 0
- Album: Workbench build
-
M
Bench Clamp Selection
OK, I have a Rockler Gift Card that has been idling since LAST Christmas. :tinysmile_cry_t: I want to use it before this Christmas comes. I need to get a bench clamp for my workbench and I have been considering one of two. The first one is their 9" Heavy Duty Quick Release Front Vise...- MarvinWatkins
- Thread
- bench clamp selection
- Replies: 5
- Forum: General Woodworking
-
Anyone tried the Bow Clamp Caul?
has anyone here tried these: http://bowclamp.com/ they look pretty useful but can two clamps distribute enough force to glue up 48" hardwood panels? THX- kooshball
- Thread
- bow caul clamp
- Replies: 11
- Forum: General Woodworking
-
HF Quick Clamp - Crap
So last week I ordered 5' of link belt for my table saw hoping to solve the issue with the table vibrating alot, especially during startup (and it DID!), and ordered a 12" quick clamp on a whim...I used a coupon for it, which made it free, plus a 20% off coupon which more than covered shipping...- buildintechie
- Thread
- clamp crap quick
- Replies: 5
- Forum: Hand Tools and their Use
-
-
-
Dressing Blade Clamp Screw on DW788
I experienced a lot of blade breakage on my DW788 awhile back. The blade clamp screw must be flat to work correctly, and my attempts at hand dressing them just wasn't good enough. I found a quick and simple way to accomplish this task. I took a piece of hardwood, approximately 1/4" thick. The...- sawman101
- Thread
- blade clamp dressing dw788 screw
- Replies: 2
- Forum: Power Tools and Their Use
-
Bobby G - Clamp run
I will be heading over there this weekend to pick up my clamps. If anyone in the Raleigh area hasn't made it yet, I can pick yours up as well. I work around Rex Hospital if you want to arrange to drop off your payment. I live in Holly Springs if you want to arrange for something in the...- zapdafish
- Thread
- bobby clamp run
- Replies: 1
- Forum: NC WW Pony Express Requests
-
Bessey clamp deal - Breaking news
The order has been placed. When I placed it, I found out that they had 2 more of the 24" so I bought them. So these are available. Also, I was able to get another $1 off on each clamp. Contact me by PM only for additional quantities or new requests. So, I have 2 - 24" available at $32 each. and...- bobby g
- Thread
- bessey breaking call clamp deal news potential update
- Replies: 26
- Forum: Found for Sale/Hot Deals
-
Clamp Rack: Weekend Project
I have wanted to find a home for my 'Bessy-Style' clamps for quite awhile, but until this weekend I never took the time to remedy the situation. I followed a plan that was in the April, 2011 issue of Fine Woodworking. All-in-all I am pleased with how it turned out. I only have 16 clamps, but I...- drw
- Thread
- clamp project rack weekend
- Replies: 6
- Forum: General Woodworking
Premier Sponsor
Our Sponsors
LATEST FOR SALE LISTINGS
-
-
-
SOLD -- $75: Gast moa v113 Vacuum Pump Veneer, 60" bag and board- Started by peterdnight
- Replies: 1
-
GONE: Gladiator 5 cleats, 10 hangers, Paper Towel and Shelf
- Started by peterdnight
- Replies: 3
-
SOLD -- $100 Makita mac700 portable air + grex pin nailer + 2 others + 50' hose
- Started by peterdnight
- Replies: 1