celtic

Celtic Cross, St. Patricks's Day, Scroll Saw Video

Hey Everyone! In this St. Patrick's Day Scroll Saw Project Video, I make this beautiful Celtic Cross designed by Jerry Bair at Dedi Woodworks (Etsy). This project uses layers of 1/4 inch material to make a beautiful 3D image! Hope you all like the video! #ArtisanPirate
- Artisan Pirate
- Thread
- Mar 6, 2023
- artisan pirate celtic cross follow irish scroll saw st patricks day subscribe woodwork youtuber
- Replies: 1
- Forum: Scrollsaw Work
Celtic Knot for Me, too...

I didn't want to high jack Sawduster's thread, so here's mine. I made this pen in March of 2011. I made the cuts on a 10" miter saw by holding the blank against a board which I had mitered at 30 degrees. In case you can't visualize that, that is my fingers WAY too close to a 10" saw blade...
- allisnut
- Thread
- Jan 23, 2012
- celtic knot
- Replies: 6
- Forum: Woodturning
Finally, a celtic knot

I have been trying to pull this off for the better part of 3 weeks now....making a jig, making it again and again :BangHead: tweaking my table, my drilling jig , putting lifts in my shoes ...wearing no shoes at all , you get the idea . This is the closest I have come so far . The pen is walnut...
- sawduster
- Thread
- Jan 22, 2012
- celtic finally knot
- Replies: 12
- Forum: Woodturning
celtic knot
- sawduster
- Media item
- Jan 22, 2012
- celtic knot
- Comments: 0
- Category: Member Galleries
Celtic, woven, 4 know trivet - Curly Maple

Four knot trivet, woven, in Curly Maple 7" x 7" x 1/2" (C6) 4 know woven Celtic Trivet 1/2" x 7" x 7" Curly Maple (C
- cskipper
- Media item
- Nov 20, 2011
- celtic trivet woven
- Comments: 0
- Album: Trivets
Celtic 4-knot trivet, woven

Woven Celtic trivet in Butternut. 5" x 5" C-4
- cskipper
- Media item
- Nov 20, 2011
- celtic trivet woven
- Comments: 0
- Album: Trivets
Celtic 6 knot trivet

Woven celtic trivet 5" x 5", Walnut
- cskipper
- Media item
- Nov 20, 2011
- celtic trivet woven
- Comments: 0
- Album: Trivets
Celtic Knot

Hello NCWW's, I have made a Celtic knot pen before after seeing Alex's Video. But has anyone turned a Celtic knot in a Bowl blank solid or Segmented Turning? It just came to me and sounded really good in my head~! :widea: :dontknow:
- MrAudio815
- Thread
- May 14, 2011
- celtic knot
- Replies: 3
- Forum: Woodturning
Celtic trivet

Maple
- cskipper
- Media item
- Dec 15, 2010
- celtic trivet
- Comments: 0
- Album: Trivets
Celtic Dagger

It has been awhile since I have posted anything on the site. I’ve gone from the dark side to the bright lights of a forge. Below is a knife I recently finished, where I used the pen turner’s technique to make a Celtic knot for the handle. The Handle is made of a maple burl and black walnut...
- KenH
- Thread
- Nov 23, 2010
- celtic celtic knot dagger
- Replies: 12
- Forum: Woodturning
turning the mallet on the lathe

turned mallet
- dpsnyder
- Media item
- Nov 22, 2010
- celtic cross mallet
- Comments: 0
- Category: Member Galleries
the finished product

turned mallet
- dpsnyder
- Media item
- Nov 22, 2010
- celtic cross mallet
- Comments: 0
- Category: Member Galleries
inserting decorative scallop

turned mallet
- dpsnyder
- Media item
- Nov 22, 2010
- celtic cross mallet
- Comments: 0
- Category: Member Galleries
glued up maple and cutting for decorative scallop

turned mallet
- dpsnyder
- Media item
- Nov 22, 2010
- celtic cross mallet
- Comments: 0
- Category: Member Galleries
final insert

turned mallet
- dpsnyder
- Media item
- Nov 22, 2010
- celtic cross mallet
- Comments: 0
- Category: Member Galleries
cutting insert #3

turned mallet
- dpsnyder
- Media item
- Nov 22, 2010
- celtic cross mallet
- Comments: 0
- Category: Member Galleries
insert #2

turned mallet
- dpsnyder
- Media item
- Nov 22, 2010
- celtic cross mallet
- Comments: 0
- Category: Member Galleries
gluing up cross insert

turned mallet
- dpsnyder
- Media item
- Nov 22, 2010
- celtic cross mallet
- Comments: 0
- Category: Member Galleries
cutting cross insert

turned mallet
- dpsnyder
- Media item
- Nov 22, 2010
- celtic cross mallet
- Comments: 0
- Category: Member Galleries
Rendered piece

This is the rendered graphic of what it should look like after the toolpath has completed (Vectric software).
- sushinutnc
- Media item
- Aug 16, 2010
- bodhran celtic drum mold
- Comments: 0
- Album: Bodhran Making