bottom

Top and Bottom plates glued and rough shaped
- MikeH
- Media item
- Feb 11, 2013
- and bottom glued plates rough shaped top
- Comments: 0
- Album: Mandolin Build
bad bottom

bad bottom
- erasmussen
- Media item
- Dec 1, 2011
- bad bottom
- Comments: 0
- Album: other
Bee Bottom Board

Bee Bottom Board
- sash plane
- Media item
- May 5, 2011
- bee board bottom
- Comments: 0
- Album: Form Photos
Bocote Bowl reversed

This is the same bowl when turned upside down.
- woodturnerdon
- Media item
- May 6, 2010
- bocote bottom bowl
- Comments: 0
- Category: Turning Projects
What does the bottom look like?

I have been told I need to do my bowls a little differently. But, I haven't seen many wood bowls and so I'm not sure what people do to the bottom. After it is all done and you put it back on the lathe what do you do to the bottom to make it more finished looking? I have been leaving the...
- Mike Davis
- Thread
- Feb 2, 2010
- bottom
- Replies: 18
- Forum: Woodturning
Sapwood_Bottom_002
- Gunslinger
- Media item
- Oct 19, 2009
- bottom sap
- Comments: 0
- Category: Member Galleries
Sapwood_Bottom_001
- Gunslinger
- Media item
- Oct 19, 2009
- bottom sap
- Comments: 0
- Category: Member Galleries
seed pot wip

border diamonds
- erasmussen
- Media item
- Aug 30, 2009
- border bottom diamond pot seed
- Comments: 0
- Album: turnings
seedpot bottom

seedpot bottom turning
- erasmussen
- Media item
- Aug 11, 2009
- bottom seedpot
- Comments: 0
- Album: turnings
bottom of turning
- erasmussen
- Media item
- Jun 17, 2009
- bottom large open segment turning
- Comments: 0
- Album: turnings
Roubo Bench-The top and the bottom meet!-Finally

Well, it was bound to happen sooner or LATER, I'm finally starting to make good progress on this puppy. After the last post(where I actually glued up the bottom section-the base) I had to place it on the top to mark out the location of the BIG mortises: After that I drilled them out with a...
- Shamrock
- Thread
- Jan 23, 2009
- benchthe bottom meetfinally roubo top
- Replies: 7
- Forum: "How To" Forum
Finger-joint Box - Help with Top & Bottom

This is one of those "just for something to do" projects. I made some improvements to my finger-joint jig and made this box to test it. The dimensions are 11"W x 11"D x 4-3/4"H. The stock is 3/8" - I think it's Alder. The finger joints look okay, so I glued up the four sides to make a box...
- KC7CN
- Thread
- Jan 11, 2009
- bottom box fingerjoint top
- Replies: 11
- Forum: General Woodworking
Harpsichord Project Part 5 - Case Bottom

Hi all, The type of instrument we are building requires the case sides to sit ON TOP of the case bottom so the next component we need to build is the Bottom of the case. It would be easier to build the Bottom out of ½” plywood but, for tonal reasons, we can’t. Instead, we will build the Bottom...
- ErnieM
- Thread
- Nov 2, 2008
- bottom case harpsichord part project
- Replies: 11
- Forum: "How To" Forum
[Other-Main Site] [Other-Main Site] number hot links at bottom of page??

Down at the bottom of the page there is a row of numbers 1 thru 90. they are hot links to the site pages, number 36 is below: Just letting you know! North Carolina Woodworker > Woodworking > Wood <hr> PDA View Full Version : Wood <hr> Pages : [1] 2 <hr> ID help? Never know what you...
- toolman
- Thread
- May 9, 2008
- bottom hot links number othermain page
- Replies: 1
- Forum: Help Desk
Nice Smooth Bottom / Longworth chuck

I found some directions online for a longworth chuck. Seemed fairly simple to make , and only cost a few dollars at Ace Hardware for some bolts wingnuts and stoppers. nothing like a nice smooth bottom:gar-La;
- owen299
- Thread
- Apr 1, 2008
- bottom chuck longworth nice smooth
- Replies: 5
- Forum: Woodturning
L
Cabinet drawer bottom question

I have a question concerning the 1/4 inch plywood that usually goes in the bottom of a drawer. These drawers are on slides and go into a pantry cabinet that is 23" deep by 18" across. Is 1/4 " heavy enough for pantry bottoms? Lorraine
- lwhughes149
- Thread
- Oct 30, 2006
- bottom cabinet drawer question
- Replies: 9
- Forum: General Woodworking
H
ShokeShaves....Flat bottom and Round Bottom?

I recently picked up a near mint Stanley #151 spokeshave with the flat bottom and it does a fine job. Seeing as I'm not too familiar with spokeshaves, I was wondering if there's a spokeshave with a rounded, concave bottom for working on rounded stock such as hickory axe handle or spokes:-D I'd...
- hk538
- Thread
- May 13, 2006
- bottom round shokeshavesflat
- Replies: 15
- Forum: Hand Tools and their Use