trash

One man's trash...

One man's trash is generally another man's trash, contrary to what you thought. However, I have a rather large assortment of walnut off-cuts and shorts and walnut firewood. I also have a friend who heats with a wood stove. If you're close by Wilton (halfway between Creedmoor and...
- Jim Murphy
- Thread
- Dec 14, 2010
- man trash
- Replies: 3
- Forum: General Woodworking
D
Question about weight of chipped wood

I have been slowly trying to get a small shop together. A dust collector and shop air cleaner are in the shop waiting for install along with a small lumber rack also waiting to be finished. I have a question as to the weight of a trash can half or slightly over with chips and dust from the...
- Dudelive
- Thread
- Jul 5, 2009
- chipped question trash weight wood
- Replies: 7
- Forum: Workshop Discussion
S
one man's trash is another man's gloat

.
- Sully
- Thread
- Mar 22, 2009
- gloat man trash
- Replies: 11
- Forum: Hand Tools and their Use
Parts list

Finished dimensions. Allow extra for milling and finishing
- Gofor
- Media item
- Jun 3, 2008
- can trash
- Comments: 0
- Album: HowIDIdIt
Face view

Face dimensions and stile/rail profiles
- Gofor
- Media item
- Jun 3, 2008
- can trash
- Comments: 0
- Album: HowIDIdIt
Top and Bottom View

Bottom panel Dimensions
- Gofor
- Media item
- Jun 3, 2008
- can trash
- Comments: 0
- Album: HowIDIdIt
More Trash

For those interested in making the angled trash can, I have uploaded a few photos (20+) in my gallery under the folder "HowIDidIt". There are currently no photos of my dimensioned drawings, as they are in pencil and are not showing up too well on a photo, but i will add them after I go over...
- Gofor
- Thread
- Jun 2, 2008
- trash
- Replies: 8
- Forum: General Woodworking
Book Matched Panel pieces

Book Matched stock
- Gofor
- Media item
- Jun 2, 2008
- can trash
- Comments: 0
- Album: HowIDIdIt
Characters

What do YOU see
- Gofor
- Media item
- May 30, 2008
- 2 4 can trash x
- Comments: 0
- Album: 2x4 project
SYP trash can

Waste baskets made of SYP (2 x 8 construction board)
- Gofor
- Media item
- May 30, 2008
- 2 4 can trash x
- Comments: 0
- Album: 2x4 project
Finish blemish

right one shows stain blotch and slight sand through of sealer
- Gofor
- Media item
- May 30, 2008
- 2 4 can trash x
- Comments: 0
- Album: 2x4 project
Trash can separator and odds and ends $40

Not mine, Raleigh craigslist. http://raleigh.craigslist.org/tls/559452796.html Roger
- sapwood
- Thread
- Feb 1, 2008
- $40 ends odds separator trash
- Replies: 1
- Forum: Found for Sale/Hot Deals
Trash Can Lid Separator Fit???

Hey gang, I ordered one of the trash can lid separators and it says it fits a standard 20" can. Well, after dragging it through the store and trying it on each variety at the BORG, I still couldn't find one that seemed to fit properly. Question: Is there supposed to be a snug fit or does...
- MikeL
- Thread
- Jan 25, 2008
- fit separator trash
- Replies: 21
- Forum: General Woodworking
GarbageBins-1

Trash and Recycle garbage bins. Made with pine.
- WoodWrangler
- Media item
- Mar 30, 2006
- bins garbage pine recycle trash
- Comments: 0
- Category: Member Galleries
Trash Can Separator Lid

Does anyone where I can get one that uses 6" hoses?
- SteveColes
- Thread
- Nov 2, 2005
- separator trash
- Replies: 8
- Forum: Where Can I Find, Buy or Sell?