tables

  1. Cypress Deck Tables

    Cypress Deck Tables

    Cypress scraps made into tables for deck, finished with Tung Oil only
    • MT native
    • Media item
    • cypress deck finish oil tables tung
    • Comments: 0
    • Category: Member Galleries
  2. Cypress Deck Tables

    Cypress Deck Tables

    Cypress scraps made into tables for deck, finished with Tung Oil only
    • MT native
    • Media item
    • cypress deck finish oil tables tung
    • Comments: 0
    • Category: Member Galleries
  3. Cypress Deck Tables

    Cypress Deck Tables

    Cypress scraps made into tables for deck, finished with 9 coats of Tung Oil only.
    • MT native
    • Media item
    • cypress deck finish oil tables tung
    • Comments: 0
    • Category: Member Galleries
  4. DavidF

    Finished at last, Bed side tables!

    Well here they are at last, it's been a long haul from when Jeff started the clock on 2/12/2007! There have been many projects along the way, but at least these are installed next to the bed they were designed for. Finish is one coat of Target coatings WB amber shellac followed by two coats...
  5. TracyP

    End Tables: Finally Done!!

    I spent some of the weekend working on the end tables I Have been planning for months. I got a lot done this weekend. I have the cases built and the tops cut to size. The only things that I have left to do is build the bases and drawers and attach the tops. Then of course comes the door...
  6. CarvedTones

    Free shop cabinets and big shop tables on CL - HURRY!

    http://raleigh.craigslist.org/zip/
  7. adowden

    Finished four maple examination tables

    When I went to pick up the vacuum press in late January I was asked to quote making four examination tables that would match some stock cabinets from Lowes. I finished those back in March. Here is a picture of the finished tables. Things I learned from this project: The best way I could...
  8. PeteM

    Bedside tables just about done . . .

    Here it is: The top is Ambrosia Maple and Claro Walnut. The base is Black Walnut ( from Jeff's first lumber run). The banding on the draw came from woodcraft. I carved the draw pull out of some mystery wood I got from Kyles cutoff pile. Right now it just has one coat of shellac on it...
  9. SRhody

    Saws, routers and tables...

    Ok, looking for some comments here, beware jumping in with both feet. Situation: Small workshop, good table saw w/fence and a Delta SH100 Router/Shaper (which does a good job for my level of projects). My problem is the SH100 doesn't really have enough surface area , but I don't have enough...
  10. G

    shimming jointer tables

    Hi All, I've been slowly trying to tune an older 8" jointer. In measuring across the tables, I find the outfeed table to sag 0.028" on the side with a rabbet ledge and 0.032" on the side with the pulley / fence. I think this is a function of both the infeed and outfeed tables sagging. If you...
  11. S

    Matching End Tables

    Tomorrow I should finish the matching end tables that go with the coffee table Cskipper posted earlier. After I drew plans for the Coffee & End Tables I made templates out of 1/4" hardboard. I used the hardboard to transfer to the wood for band sawing, routing, and to make sure all the through...
  12. michaelgarner

    Purple Heart Tables.

    Sorry for the bad pics, the camera had dust on the lens. This was done for a customer. M&T finished with Maloof oil and wax. Pretty simple design.
  13. PeteM

    Bedside tables - WIP

    Hopefully these will get done faster than the headboard. Walnut from Jeff. The idea is from the Creole Table. They are smaller than the original and I didn't like the bent legs in the smaller size so I went with plain tapers. Joinery is loose M&T - mortises cut using the Hawk RouterShop pete
  14. Bedside Tables

    Bedside Tables

    Walnut Bedside Tables
    • PeteM
    • Media item
    • bedside tables walnut
    • Comments: 0
    • Album: Bedside Tables
  15. Joe Scharle

    End Tables

    One of my girls wanted the old set, so I made some new. Coffee table next after I figure out how it should look.
  16. End table with legs dry fitted

    End table with legs dry fitted

    End table with legs dry-fitted. This will still have some modifications, but isn't it great?
    • cskipper
    • Media item
    • end tables
    • Comments: 0
    • Album: Misc
  17. cskipper

    QS Sycamore & walnut coffee & end tables

    John (Stoneskipper) has been designing a coffee and end tables for us. They are made from the QS sycamore we got from Jeff and walnut. Instead of using biscuit joinery they are tongue and grooved. The legs will be walnut, curved and mortise and tenon through the table top. The coffee table will...
  18. End table tops dry-fitted

    End table tops dry-fitted

    QS sycamore and walnut end table tops dry fitted
    • cskipper
    • Media item
    • end qs sycamore tables
    • Comments: 0
    • Album: Coffee and end tables
  19. DaveO

    NCwoodworker designed end tables

    Thanks to all for the advice/guidance on the design of my Sycamore and Walnut end tables. I took most of the suggestions that were offered and I really think that the tables benefited from them. The legs were tapered, a shelf added, aprons narrowed, and the top edges beveled. I am applying the...
  20. DaveO

    End tables WIP, this weekends efforts

    My wife decided that we needed a new couch after my daughter got sick on the old one. That new couch is too tall for the original end tables I made a few years ago. So my current project is a set of new end tables. I have some QS Sycamore from Jeff, just enough for the tops, and a bunch of Black...

Premier Sponsor

Our Sponsors

LATEST FOR SALE LISTINGS

Top