panels

  1. Beech Headboard

    Beech Headboard

    Euro Beech Headboard with Cherry panels
    • PeteM
    • Media item
    • beech cherry euro headboard panels with
    • Comments: 0
    • Category: Member Galleries
  2. W

    cherry panels sale or trade

    Cleaning shop and have some cherry panels to get rid of. These panels were glued up professionally for me. Some are on mdf but most are on chip board substrate. These are of various sizes as they were to build a room full of built in cabinets for an office area. After 10-15 years its time to...
    • wayne
    • Thread
    • cherry panels sale trade
    • Replies: 3
    • Forum: Wood
  3. J

    Prefinished panels

    Where can I purchase. The type used in closet built ins I think its covered with vinyl. Thanks Dwight
  4. zapdafish

    anyone have solar panels on their roof?

    Anyone using solar power with their HVAC? I recently had my HVAC upgraded with a solar ready unit. The company that installed the unit let me know that with rebates and discounts, the $8000 cost for adding solar panels will cost me only $800. It seems pretty tempting but not sure if installing...
  5. NCTurner

    Great Write Up on PS, RS, and QS in oak frames and panels

    Author: Tom Sontag Paying attention to grain patterns with ring porous hardwoods like oak and ash is an important step in a woodworker's maturation adn a big part pf whether a design succeeds or not. I still have a piece or two I made before I discovered this and frankly, they are hard to look...
  6. LeftyTom

    Flattening Glued Up Panels

    I have glued up some more panels, with better results than my first go at it (Thanks again, Jay Brewer). These panels have one or two spots on the glue seams that are .030 and .040 inch off (higher or lower, depends on how you think about it). There are no gobs of dried glue visible, but the...
  7. LeftyTom

    Winston Area: Where Can I get Panels Sanded?

    I have four panels (two 15" x 22", two 23" x 30") that I need sanded from about 9/16" to a final thickness of about 1/2". Anyone have ideas of where I can buy/borrow time of a wide belt sander? Before you ask, I do not have a handplane.
  8. K

    Attaching Solar Panels

    Looking to install a solar system, I am in inquiring to see if there is anyone who has done this before. There appears to be some standard frames used for attaching solar panels to the roof. Has anyone used another method using materials purchased at the lumber yard?
  9. B

    Raised panels on the shaper

    Just did up these photos so I thought I would share them here. This is a shop-made fence for doing raised panels safely. Edgeband a piece of 3/4 plywood with hard wood like maple. Drill a hole for the spindle. Clamp the plywood. Install the cutter and lower the cutter into the wood to make...
  10. C

    Roof Panels

    I'm just getting into building bird feeders. I see most of the ones at Lowes has a panel that looks like lapped planks. This is a milled t&g piece approx 4" wide. Does any one know of a source for something like this? Thanks,
  11. B

    Looking for glued furniture panels.

    I know the furniture industry in NC has tanked but I'm looking to buy panels up to 18" x 18"x 1.5- 2" thick. The panels are typically made up of pieces 1" to 3" wide. Need 'em for bowl turning. I only know of one place in Maine that still sells them but I hope there's something closer. Any...
  12. mdelgiorno

    Walnut wall panels - miter madness!

    Here's an in-progress shot of some walnut wall paneling I'm putting up in my home/office. I couldn't find any overlay molding that I liked, so I sketched some up and the Hardwood Store in Gibsonville did a great job making it. Maybe I should have thought about the number of miter cuts before I...
  13. KC7CN

    How do you build wide-frame panels

    I want to construct a couple of panels similar to the image below - about 1-3/8" mitered frame and 3/4" Oak veneer plywood. Although I've done this before (see thumbnail picture below), the joint between the veneer and the plywood was separated with a "V" grove - not a flush joint like...
  14. W

    I am Willing to pay to have 5 Panels run through drum sander>

    I am making my daughter a cherry chest and I need 5 glued up panels run through a drum sander. These are 18 inchs wide made of kiln dried cherry and are a bit too much for me to sand down with an orbital sander. I am new to the area and don't know where I can go to get this type of service, so...
  15. flatheadfisher

    Question About Gluing Panels

    For my next project, I need to make a long panel that will be our kitchen counter top. I am using 8/4 hard maple. I finished the small top and it looks like this: It is face grain and will be finished on both sides with Waterlox. The rest of the counter top will be 18' long. The...
  16. Oak dresser Side Panel

    Oak dresser Side Panel

    Tongue and Groove panels with mortise and tendon legs
    • skysharks
    • Media item
    • panels side
    • Comments: 0
    • Category: Furniture Projects
  17. BKind2Anmls

    Gaps in Glued-Up Panels

    First the history: I glued up several panels for a high chair/rocking horse/desk combo piece of furniture. I took flat-sawn red oak and cut it into 1X1 strips. After jointing, planing, etc. I turned the strips 90 degrees so that the flat-sawn sides were glued together and straight grain...
  18. Bas

    Biscuits , Frames and Panels *MORE PROGRESS (and pictures)*

    I started a new project, this will be a cabinet to put my bird cage on (one of the legs broke off, and it's been resting on a piece of PT 2x4 for 6 months now....). The cabinet will have a big shelf for the kitty litterbox. I liked the episode on the Woodsmith Shop on making frames and panels...
  19. J

    Corner Cupboard progress--door panels

    I thought that birdseye maple door panels would add some bling to the walnut cabinet and keep it from looking so dark. The maple boards have had about a month to adjust to the shop, so I split them this morning. For you hand tool users, I used a bandsaw, but could have used a frame saw. Bandsaw...
  20. K

    Raised panels- new Woodsmith

    Just finished a quick scan of the raised panel bits article in the new WS mag. It brought to mind something I have struggled with in the past when making raised panels. This struggle is one of the reasons I have not made many raised panels. I have always made the panels stand proud of the rails...

Premier Sponsor

Our Sponsors

LATEST FOR SALE LISTINGS

Top