adjusting
-
Adjusting sawstop fence
Sawstop fence issue Ok, I took a video of my issue. My dial is snug in there so that's not the issue. Also the fence is not moving. My shed isn't insulated yet and can get pretty hot/humid. Could the MDF have swelled at the end. Any suggestions?- Rhythm House Drums
- Thread
- adjusting fence sawstop
- Replies: 7
- Forum: Power Tools and Their Use
-
L
adjusting miter and table saw
I am a novice woodworker at best and need help adjusting a new mitre saw and checking my table saw, and bandsaw. I expect to pay someone for help. I am located in Greensboro, NC.- Larry R. Tysinger
- Thread
- adjusting miter table
- Replies: 9
- Forum: Power Tools and Their Use
-
Krenov style wood plane and adjusting mallet
For father's day my children got me David Finck's Making and Mastering Wood Planes. I really enjoyed reading this book. Well written and it covers much more than just how to make a plane. David seems like a really nice guy too. In the course of making the plane I emailed him and got a quick...- eyekode
- Thread
- adjusting krenov mallet plane style wood
- Replies: 6
- Forum: Hand Tools and their Use
-
5/8" brass rod for plane adjusting hammer?
Any recommendations of where to buy some 5/8" brass rod in the Apex/Raleigh/Durham area? I would like to make plane adjusting hammer for the wood plane(s) I am finishing up. Thanks! Salem- eyekode
- Thread
- 5 or 8 adjusting brass hammer plane rod
- Replies: 12
- Forum: Where Can I Find, Buy or Sell?
-
Handling or Adjusting for Run Out
Hi All, I turn long thin spindles for making flutes(25 to 30 " long with 7/8 , 3/4 or 1 " bores)....I dont have a modern lathe but an older Craftsman with the tubular bed. I basically take 2 pieces of stock and rout half the bore of the flute in each and glue these together. Then I...- Flute Maker
- Thread
- adjusting handling run
- Replies: 8
- Forum: Woodturning
-
L
Adjusting new table saw
I have recently had an eye problem and it has affected my depth sight so I thought I needed to buy a Saw Stop to protect my fingers which I did. Now due to my sight problem I can't seem to get the blade square to the mitre slot. I would like to hire some one to give me hand. PM me for...- Larry R. Tysinger
- Thread
- adjusting table
- Replies: 4
- Forum: Power Tools and Their Use
-
Adjusting speeds on Bosch jigsaw
OK, so I got the Bosch jigsaw so many folks recommended (photos and a proper gloat forthcoming). I have been doing a few things with it and I am quite impressed so far. I used the circle jig to cut a bowl blank out of some dry 8/4 spalted maple. I ripped oddball shaped green log sections to...- CarvedTones
- Thread
- adjusting bosch jigsaw speeds
- Replies: 6
- Forum: Power Tools and Their Use
-
L
Adjusting Miter Saw
I have a Hitachi Slide Compund Miter Saw model 8-1/2 C8FB2 that I can't seem to get square. I have the booklet that came with the saw but there does not seem to be any adjustment infromation. I have emailed Hitachi and did not get a reply. The only thing I can figure out to adjust is the...- Larry R. Tysinger
- Thread
- adjusting miter
- Replies: 3
- Forum: Power Tools and Their Use
-
Help with adjusting a mortise...
Many of you have been looking at my Workbench base WIP thread. I finally got the mortises finished on one of the feet and when I put the second one in it is a little out of square. See the pic below: Is it better to leave the integrity of the mortise and tenon alone and gently coax...- MikeH
- Thread
- adjusting mortise
- Replies: 13
- Forum: General Woodworking
