motor

  1. Universal Motor Brushes

    Universal Motor Brushes

    Universal Motor Brush from PC 690 Router. This closeup shows the brush, brush assembly and commutator from another angle.
    • ehpoole
    • Media item
    • brush brushes motor universal
    • Comments: 0
    • Album: Universal Motor Brushes
  2. Universal Motor Brushes

    Universal Motor Brushes

    Universal Motor Brush from PC 690 Router. This closeup shows the carbon brush (barely shown in center), brush assembly (left) and motor commutator (right).
    • ehpoole
    • Media item
    • brush brushes motor universal
    • Comments: 0
    • Album: Universal Motor Brushes
  3. Universal Motor Brushes

    Universal Motor Brushes

    Universal Motor Brush from PC 690 Router. Another view, again notice the curvature of the brush where it mates with the commutator (left side). Also shown is the spring and the braided conductor wire.
    • ehpoole
    • Media item
    • brush brushes motor universal
    • Comments: 0
    • Album: Universal Motor Brushes
  4. Universal Motor Brushes

    Universal Motor Brushes

    Universal Motor Brush from PC 690 Router. Notice curvature of brush where it mates with the commutator and smooth face.
    • ehpoole
    • Media item
    • brush brushes motor universal
    • Comments: 0
    • Album: Universal Motor Brushes
  5. D

    Grizzly BS with motor brake?

    I'm looking at getting a bandsaw. Based on numerous reviews and my own comparisons, I think that I'll be getting either a 17" or a 19" Grizzly (bigger is better, right?). Does anybody here have one of Grizzly's BS with a motor brake rather than a foot brake? Is it worth the extra $155 to...
  6. James Davis

    Electric Motor Problem?

    I have a Dayton 1 1/2 hp motor on a compressor. It will start up fine while there is no air pressure in the tank, but when the tank starts to get full sometimes it will trip the breaker before it gets full or most of the time it will pump it all the way up and then trip when it tries to start up...
  7. J

    6" Powermatic joiner $50.00 not mine, no motor

    Avoid scams and fraud by dealing locally! Beware any deal involving Western Union, Moneygram, wire transfer, cashier check, money order, shipping, escrow, or any promise of transaction protection/certification/guarantee. More info Joiner - $50 (Mooresville) Date: 2010-07-29, 1:49PM EDT Reply...
  8. J

    unisaw motor, not mine

    http://eastnc.craigslist.org/tls/1858541934.html eastern NC craigslist > for sale / wanted > tools please flag with care: miscategorized prohibited spam/overpost best of craigslist Avoid scams and fraud by dealing locally! Beware any deal involving Western Union, Moneygram, wire...
  9. W

    Buffing motor rotation problem...

    Okay, here's my problem.I bought a 1/2 hp 1725 motor in anticipation of getting the beale buffing system.I picked that up over the weekend and got to setting up my motor and low and behold I turn it on and off the buff comes from the motor.ARGHHHH...I bought a clockwise rotating motor...
  10. kooshball

    I wonder what kind of motor I actually have on my HF 2hp dust collector???

    Ok, so the internet and the manual for the 2HP HF dust collector say that my motor is 20a but the machine label says that it is 14a, then I look at the cord and see that it is 16AWG which according to this link is good only for 10a: http://www.epanorama.net/documents/wiring/wire_resistance.html...
  11. sawduster

    New motor for my Jet mini ( gloat )

    Found a bigger motor for my lathe today :icon_thum It came attached to a new Delta 46-460 :banana: Thanx to Klingspor for the hook-up :notworthy: YOU ROCK !! View image in gallery View image in gallery Man this sucker is solid !! Variable speed and reversible :banana: View image in...
  12. sawduster

    Funeral for a lathe motor ?

    The motor on my Jet midi has developed a small squeak and has stiffened up considerably . I have checked it without the belt also and it is the same . Does anyone know if this can be checked or lubricated somehow ? I'm sure it will only get worse I'm going to look at warranty but i am not the...
  13. clawofthebear

    Shopsmith motor question

    Okay folks, this is a gloat and a sob story rolled into one. My brother and I have been remodeling my mom's house for the past six months. Complete tearout...only studs left when we started refinishing. My mom felt bad, because we have spent probably 5 hours a day for six months after our other...
  14. S

    Electric motor - $25 (Zebulon (Pilot))

    Not mine http://raleigh.craigslist.org/tls/1645494506.html Electric motor - $25 (Zebulon (Pilot)) Date: 2010-03-15, 4:58PM EDT Reply to: sale-janpm-1645494506@craigslist.org [Errors when replying to ads?] 1HP electric motor came off a bandsaw. Works fine. Location: Zebulon (Pilot) it's...
  15. S

    motor shaft change with Reeves drive

    Hi all, I need to find out if it is possible to get an adapter or do whatever I have to do to switch a lame Harbor Fright Chinese motor with a really nice Baldor motor I have. The sticking point is that the original HF motor has about a 4" long shaft (5/8") which it appears to fully need for...
    • sasjzl
    • Thread
    • change drive motor reeves shaft
    • Replies: 4
    • Forum: Woodturning
  16. eyekode

    Any use of a burnt out motor?

    I have a ~3/4 HP Grizzly motor that doesn't work anymore. I opened the back and the windings look like they may have shorted. But I hate taking things to the dump. If anyone has a use for this motor you are welcome to have it! Salem
  17. rcflyer23

    Looking for a motor for Craftsman TS

    I need to find a motor for a Craftsman Table saw mine gave up the ghost this afternoon. It still gets power it just hums and will not turn the drive shaft. Not sure if its the brushes or just needs a rebuild but wanted to check here and see if anyone may have one that is compatible that they...
  18. mbeach

    Delco 1/6 HP 1725 RPM motor... what to make?

    I have a 1/6 hp 1725 rpm Delco motor that was given to me, it has a pulley on it and he gave me an attachment for like a grinding wheel or buffing station. So... what should i make? I have a grinder already, dont have a buffing station... but not sure i really need one right now... Any...
  19. rick7938

    Woodworking Application for Electric Motor

    I have a nice GE 1/2-hp 1750 rpm electric motor that I am wanting to put to some good woodworking application. It has a single 1/2-inch shaft with a flat for a set-screw. How can I put this motor to good woodworking use? I can't stand having a perfectly good motor and not having it earning its...
  20. S

    Delta Motor

    Looking to buy or trade for a older Delta 1725 Rpm motor. Prefer 1/2" shaft 1ph. 1/3hp to 3/4hp 1ph. thank you

Premier Sponsor

Our Sponsors

LATEST FOR SALE LISTINGS

Top