Klingspor's Woodworking Shop (Festool) Ad #2

Special Events in the next 30 days

Results 1 to 8 of 8
  1. #1
    Corporate Member
    DQ
    Raymond's Avatar
    Nickname
    Raymond (64)
    Join Date
    Jul 2012
    Location
    Charlotte, NC
    Posts
    1,952
    Visit Freq
    7.00 visits/week
    Threads
    63
    Classifieds
    0

    59-1/2" Band Saw Blades

    After 20 years of service, my benchtop band saw bit the dust. The Blade Tension Housing (pot metal) broke today and, of course, being a Delta that part is no longer available through ereplacements.com. I have searched for the past two days with no luck of finding that part.

    So if someone out there has a use for 8 brand new (still in the packaging) 59-1/2 band saw blades, let me know - they are free for the taking.

    3 each 6 TPI blades; 3 each 15 TPI blades; 2 each 18 TPI blades.
    I like making things. I have a wood shop at home. I am a terrible carpenter but I love doing it. Raymond - Charlotte, NC

  2. The following 4 users say Thank You to Raymond :


  3. #2
    User dazart's Avatar
    Nickname
    Steve
    Join Date
    Jun 2017
    Location
    Huntersville, NC
    Posts
    184
    Visit Freq
    2.19 visits/week
    Threads
    31
    Classifieds
    0

    Re: 59-1/2" Band Saw Blades

    when do you use the benchtop vs. regular?

  4. #3
    Corporate Member
    DQ
    Raymond's Avatar
    Nickname
    Raymond (64)
    Join Date
    Jul 2012
    Location
    Charlotte, NC
    Posts
    1,952
    Visit Freq
    7.00 visits/week
    Threads
    63
    Classifieds
    0

    Re: 59-1/2" Band Saw Blades

    Steve, I normally use the benchtop when I am handling pieces smaller than 9" wide and no more than 3" inches thick. Usually, this is for items that I am going to throw on the lathe. It was faster than pulling out my larger band saw and setting it up.
    I like making things. I have a wood shop at home. I am a terrible carpenter but I love doing it. Raymond - Charlotte, NC

  5. #4
    Master of None User
    DQ
    CDPeters's Avatar
    Nickname
    Chris (54)
    Join Date
    Oct 2010
    Location
    Windsor, VA
    Posts
    890
    Visit Freq
    2.77 visits/week
    Threads
    42
    Classifieds
    0

    Re: 59-1/2" Band Saw Blades

    Raymond, what part specifically do you need? I just parted out an old (probably about 20+ years?) Delta 9" bandsaw - I think the model was 28-150 - not sure on that though. If mine is same as yours, I'd be glad to sent you the parts you need.

    A picture of what is needed might be useful to insure it's the right one...

    HTH,
    Chris
    "Remember - If the women don't find ya handsome, they should at least find ya handy!" - Red Green
    "Always take hold of things by the smooth handle." - Thomas Jefferson

  6. The following user says Thank You to CDPeters for this useful post:


  7. #5
    Corporate Member
    DQ
    Raymond's Avatar
    Nickname
    Raymond (64)
    Join Date
    Jul 2012
    Location
    Charlotte, NC
    Posts
    1,952
    Visit Freq
    7.00 visits/week
    Threads
    63
    Classifieds
    0

    Re: 59-1/2" Band Saw Blades

    Chris, the part is called the Tension Housing (78 and 76). The housing broke right where the pin (77 and 77A) connected the upper and lower housings together.

    Attached Images Attached Images
    I like making things. I have a wood shop at home. I am a terrible carpenter but I love doing it. Raymond - Charlotte, NC

  8. #6
    Master of None User
    DQ
    CDPeters's Avatar
    Nickname
    Chris (54)
    Join Date
    Oct 2010
    Location
    Windsor, VA
    Posts
    890
    Visit Freq
    2.77 visits/week
    Threads
    42
    Classifieds
    0

    Re: 59-1/2" Band Saw Blades

    Roger that Raymond. I think I have those parts, I'll check when I get home. PM me your address and I will mail them off to you.
    "Remember - If the women don't find ya handsome, they should at least find ya handy!" - Red Green
    "Always take hold of things by the smooth handle." - Thomas Jefferson

  9. The following 6 users say Thank You to CDPeters :


  10. #7
    Corporate Member
    DQ
    Raymond's Avatar
    Nickname
    Raymond (64)
    Join Date
    Jul 2012
    Location
    Charlotte, NC
    Posts
    1,952
    Visit Freq
    7.00 visits/week
    Threads
    63
    Classifieds
    0

    Re: 59-1/2" Band Saw Blades

    A big THANK YOU to Chris (CDPeters) for sending me the parts to repair my benchtop band saw. Chris is one of the reasons NCWW is so outstanding!
    I like making things. I have a wood shop at home. I am a terrible carpenter but I love doing it. Raymond - Charlotte, NC

  11. The following 5 users say Thank You to Raymond :


  12. #8
    Master of None User
    DQ
    CDPeters's Avatar
    Nickname
    Chris (54)
    Join Date
    Oct 2010
    Location
    Windsor, VA
    Posts
    890
    Visit Freq
    2.77 visits/week
    Threads
    42
    Classifieds
    0

    Re: 59-1/2" Band Saw Blades

    Glad to help out Raymond and glad they were the right parts. I literally stripped those parts the day before your original post - talk about the stars aligning!

    Cheers,
    C.
    "Remember - If the women don't find ya handsome, they should at least find ya handy!" - Red Green
    "Always take hold of things by the smooth handle." - Thomas Jefferson

Similar Threads

  1. Band saw blades
    By chasbwdc in forum Where Can I Find, Buy or Sell
    Replies: 5
    Last Post: 12-29-2014, 10:54 AM
  2. Band saw blades
    By chasbwdc in forum Help Desk
    Replies: 1
    Last Post: 12-28-2014, 09:06 AM
  3. Used band saw blades ?
    By Bill Clemmons in forum Found for Sale/Hot Deals
    Replies: 9
    Last Post: 08-02-2013, 12:33 PM
  4. Band Saw Blades
    By sawman101 in forum General Woodworking
    Replies: 15
    Last Post: 12-02-2010, 03:21 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •