Klingspor's Woodworking Shop (Locations)

Special Events in the next 30 days

Results 1 to 5 of 5
  1. 07-15-2017, 07:14 PM #1
    Robert166
    Robert166 is offline
    User
    Nickname
    robert166
    Join Date
    Nov 2013
    Location
    Pikeville, NC
    Posts
    88
    Visit Freq
    2.31 visits/week
    Threads
    29
    Classifieds
    0

    Let's make a deal!

    I have approximately 75 walnut rough cut boards. Most of it is 6 inches wide, 8 foot long. Air dried, ready to be used. Willing to trade for cutting and planing it to standard dimensions for me. I don't have the equipment to do this. But if you do and need some walnut, let's deal.
  2. 07-16-2017, 11:37 AM #2
    MarkE
    MarkE is offline
    Administrator Corporate Member
    DQ     MarkE's Avatar
    Nickname
    Mark (62)
    Join Date
    Dec 2009
    Location
    Willow Spring, NC
    Posts
    4,085
    Visit Freq
    6.77 visits/week
    Threads
    270
    Classifieds
    0

    Re: Let's make a deal!

    If you are willing to make the hour or so drive out here to Willow Spring, I can help you get those boards dimensioned.
    “I know you believe you understand what you think I said, but I am not sure you realize that what you heard is not what I meant.”
  3. 07-16-2017, 02:21 PM #3
    Robert166
    Robert166 is offline
    User
    Nickname
    robert166
    Join Date
    Nov 2013
    Location
    Pikeville, NC
    Posts
    88
    Visit Freq
    2.31 visits/week
    Threads
    29
    Classifieds
    0

    Re: Let's make a deal!

    Scott Smith sent me a pm, hoping to hammer out the deal.

  4. The following user says Thank You to Robert166 for this useful post:

    ScottM
  5. 07-16-2017, 06:15 PM #4
    MarkE
    MarkE is offline
    Administrator Corporate Member
    DQ     MarkE's Avatar
    Nickname
    Mark (62)
    Join Date
    Dec 2009
    Location
    Willow Spring, NC
    Posts
    4,085
    Visit Freq
    6.77 visits/week
    Threads
    270
    Classifieds
    0

    Re: Let's make a deal!

    Excellent. Hope it all works out.
    “I know you believe you understand what you think I said, but I am not sure you realize that what you heard is not what I meant.”
  6. 07-18-2017, 02:15 PM #5
    Robert166
    Robert166 is offline
    User
    Nickname
    robert166
    Join Date
    Nov 2013
    Location
    Pikeville, NC
    Posts
    88
    Visit Freq
    2.31 visits/week
    Threads
    29
    Classifieds
    0

    Re: Let's make a deal!

    Going to see Scott tomorrow and get some nice walnut! I will probably have some for sale afterwards.

  7. The following user says Thank You to Robert166 for this useful post:

    LeftyTom
« Previous Thread | Next Thread »

Similar Threads

  1. When I can't make sawdust - I watch someone else make sawdust!
    By Hmerkle in forum General Woodworking
    Replies: 10
    Last Post: 12-31-2015, 07:06 PM
  2. Who Wants To Make A Deal?
    By steviegwood in forum Woodturning
    Replies: 10
    Last Post: 03-19-2010, 07:56 AM
  3. Good Deal or Bad Deal - Drill Press
    By mbeach in forum Power Tools and Their Use
    Replies: 14
    Last Post: 12-29-2009, 08:13 AM
  4. Good deal at Lowe's Frued router deal...but they still took me for 10 bucks
    By newtonc in forum Found for Sale/Hot Deals
    Replies: 4
    Last Post: 12-21-2008, 09:02 PM
  5. How do I make this cut?
    By cpowell in forum General Woodworking
    Replies: 10
    Last Post: 03-30-2006, 09:42 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules