Klingspor's Woodworking Shop (Locations)

Special Events in the next 30 days

Page 2 of 2 FirstFirst 1 2
Results 16 to 28 of 28
  1. #16
    Newbie
    Nickname
    Bryan
    Join Date
    Mar 2017
    Location
    Matthews, NC
    Posts
    25
    Visit Freq
    3.25 visits/week
    Threads
    5
    Classifieds
    0

    Re: Crosscut sled construction - what to use for the runners?

    Quote Originally Posted by Michael Mathews View Post
    I use the UHMW. I get large sheets of scrap from work that are about an inch thick x 2' x3'. I mill them on the TS and jointer all the same. They work great and don't bind. They add a bit of slipperiness to the runners...IMO
    You should offer up 1" X 1" X 2' strips of this for sale, sounds like people could make good use of them.

  2. #17
    User
    Nickname
    Brogan
    Join Date
    Jan 2017
    Location
    Morrisville, NC
    Posts
    262
    Visit Freq
    7.00 visits/week
    Threads
    20
    Classifieds
    0

    Re: Crosscut sled construction - what to use for the runners?

    Agreed.

    I'd definitely purchase several for the jigs I plan to make.

    The picnic would be an ideal place/time to sell them

  3. #18
    Senior User
    DQ
    redknife's Avatar
    Nickname
    Chris
    Join Date
    May 2013
    Location
    Lewisville, NC
    Posts
    673
    Visit Freq
    7.04 visits/week
    Threads
    66
    Classifieds
    0

    Re: Crosscut sled construction - what to use for the runners?

    Quote Originally Posted by Brogan View Post
    Agreed.

    I'd definitely purchase several for the jigs I plan to make.

    The picnic would be an ideal place/time to sell them
    As an aside, Klingspor now carries 3/4" wide, 3/8" deep, 4' long UHMW for 9.99
    http://www.woodworkingshop.com/product/ph11210/

  4. #19
    User
    Nickname
    Brogan
    Join Date
    Jan 2017
    Location
    Morrisville, NC
    Posts
    262
    Visit Freq
    7.00 visits/week
    Threads
    20
    Classifieds
    0

    Re: Crosscut sled construction - what to use for the runners?

    Not a bad price for the UHMW but the flat rate shipping cost makes it more expensive than other places if it's the only thing being purchased.

  5. #20
    Senior User
    DQ
    redknife's Avatar
    Nickname
    Chris
    Join Date
    May 2013
    Location
    Lewisville, NC
    Posts
    673
    Visit Freq
    7.04 visits/week
    Threads
    66
    Classifieds
    0

    Re: Crosscut sled construction - what to use for the runners?

    Quote Originally Posted by Brogan View Post
    Not a bad price for the UHMW but the flat rate shipping cost makes it more expensive than other places if it's the only thing being purchased.
    True just meant they have it in store for those close enough.

  6. #21
    User
    Nickname
    Brogan
    Join Date
    Jan 2017
    Location
    Morrisville, NC
    Posts
    262
    Visit Freq
    7.00 visits/week
    Threads
    20
    Classifieds
    0

    Re: Crosscut sled construction - what to use for the runners?

    That's a good point - I'm so used to shopping online I always forget about physical stores.

  7. #22
    Board of Directors
    Treasurer
    Corporate Member
    DQ
    Michael Mathews's Avatar
    Nickname
    Michael (54)
    Join Date
    Mar 2012
    Location
    Chapel Hill, NC
    Posts
    1,132
    Visit Freq
    6.92 visits/week
    Threads
    110
    Classifieds
    0

    Re: Crosscut sled construction - what to use for the runners?

    Bryan, next time you're in Chapel Hill, let me know with some lead time and you can stop at my shop and we'll cut you a piece. I get it for the cost of asking and hauling it home. No need for me to sell it.

    Brogan, you're always welcome to stop by too.

    Quote Originally Posted by Gilley23 View Post
    You should offer up 1" X 1" X 2' strips of this for sale, sounds like people could make good use of them.

  8. The following 2 users say Thank You to Michael Mathews :


  9. #23
    User
    Nickname
    Bruce
    Join Date
    Nov 2005
    Location
    Apex, NC
    Posts
    5,277
    Visit Freq
    6.31 visits/week
    Threads
    896
    Classifieds
    0

    Re: Crosscut sled construction - what to use for the runners?

    Quote Originally Posted by Brogan View Post
    That's a good point - I'm so used to shopping online I always forget about physical stores.
    Again, get your saw, and I will mill you a couple runners. I buy the 1" X 3/8" wear strips from AgriSupply in Garner. The last ones I bought were around $16 for a 10' length. Rip them to a little over 3/4", then plane to size. I built a sled to run them through planer for exact fit

  10. The following user says Thank You to junquecol for this useful post:


  11. #24
    User
    Nickname
    Brogan
    Join Date
    Jan 2017
    Location
    Morrisville, NC
    Posts
    262
    Visit Freq
    7.00 visits/week
    Threads
    20
    Classifieds
    0

    Re: Crosscut sled construction - what to use for the runners?

    Quote Originally Posted by junquecol View Post
    I built a sled to run them through planer for exact fit
    So you built a sled to make some runners to build a sled

  12. #25
    Board of Directors
    Secreatary
    Corporate Member
    DQ
    Mike Davis's Avatar
    Nickname
    Mike
    Join Date
    Dec 2005
    Location
    Walnut Cove, NC
    Posts
    10,901
    Visit Freq
    7.00 visits/week
    Threads
    613
    Classifieds
    0

    Re: Crosscut sled construction - what to use for the runners?

    I make most of my runners with maple, sometimes I varnish it and wax it but sometimes I'm in a hurry and don't. I make the runners long so there is less side to side movement. Double runners sometimes and single sometimes depending on what I'm making.

    Somebody gave me or I bought in a lot some of the aluminum runners but I haven't had a critical application that deserved the extra accuracy yet.

    I look at jigs as disposable items sorta like sandpaper. If I could I would dispose of all of them. But, they do come in handy once in a while.



    One machine can do the work of 50 ordinary men. No machine can do the work of one extraordinary man." -Elbert Hubbard

    WWFD

  13. #26
    Senior User
    Nickname
    Bob Vaughan
    Join Date
    Sep 2009
    Location
    Roanoke, VA
    Posts
    430
    Visit Freq
    5.46 visits/week
    Threads
    13
    Classifieds
    0

    Re: Crosscut sled construction - what to use for the runners?

    What about standard 3/8 x 3/4 cold rolled 1018 steel from Speedy metals?
    That's what I use. I'll get them 18" long or 24" long.
    Drill and tap for whatever or drill for screws into the sliding panel.
    The older Sears saws used a smaller slot (-.005Ī) so they won't work there, but for other saws, its perfect.

  14. #27
    User
    Nickname
    Bruce
    Join Date
    Nov 2005
    Location
    Apex, NC
    Posts
    5,277
    Visit Freq
    6.31 visits/week
    Threads
    896
    Classifieds
    0

    Re: Crosscut sled construction - what to use for the runners?

    Quote Originally Posted by bob vaughan View Post
    What about standard 3/8 x 3/4 cold rolled 1018 steel from Speedy metals?
    That's what I use. I'll get them 18" long or 24" long.
    Drill and tap for whatever or drill for screws into the sliding panel.
    The older Sears saws used a smaller slot (-.005Ī) so they won't work there, but for other saws, its perfect.
    Dillon Supply stocks 1018 in twelve foot lengths. Last I bought was around $36. It's been a couple years now.

  15. #28
    Staff Advisor
    Corporate Member
    DQ
    Joe Scharle's Avatar
    Nickname
    Joe (74)
    Join Date
    Sep 2005
    Location
    New Bern, NC
    Posts
    5,370
    Visit Freq
    6.65 visits/week
    Threads
    675
    Classifieds
    0

    Re: Crosscut sled construction - what to use for the runners?

    3/4" aluminum flat bar from the BORGs works well. Just drill and countersink. Dbl sided tape or hot melt glue will hold until you get it screwed in.
    Always be yourself because the people that matter don't mind, and the ones who mind, don't matter.

Similar Threads

  1. My crosscut sled
    By merrill77 in forum General Woodworking
    Replies: 2
    Last Post: 11-21-2009, 11:08 PM
  2. Crosscut Sled
    By thrytis in forum General Woodworking
    Replies: 16
    Last Post: 10-14-2007, 09:11 PM
  3. crosscut sled
    By erasmussen in forum Workshop Discussion
    Replies: 8
    Last Post: 03-22-2007, 01:06 AM
  4. Another crosscut sled
    By chris99z71 in forum General Woodworking
    Replies: 17
    Last Post: 10-05-2006, 10:30 PM
  5. Tablesaw crosscut sled
    By Travis Porter in forum General Woodworking
    Replies: 6
    Last Post: 02-22-2006, 08:01 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •