veneer
-
Jewelry Box WIP
I'm done with the case and lid for 2 jewelry boxes made of teak. in the third picture you can see the lid is curved. Size: 14.5 wide and 10" deep and 10" tall. think....tall toaster oven. it is made of layers of 1/8 inch bending plywood, shaped on a bending form in a vacuum bag. the front...- BKHam
- Thread
- jewelry box sliding dovetails teak veneer
- Replies: 25
- Forum: General Woodworking
-
Bench top tool cabinet (side)
Side view of a tool cabinet I made to sit on top of my work bench (over the tool tray). The side and drawer fronts are book-matched sweet gum veneer. The cock beading around the drawers is pecan.- creasman
- Media item
- cockbead pecan sweet gum veneer
- Comments: 0
- Category: Member Galleries
-
Bench top tool cabinet (back)
Back view of a tool cabinet I made to sit on top of my work bench (over the tool tray). Also, shows the marquetry image on the base section.- creasman
- Media item
- marquetry pecan sweet gum veneer
- Comments: 0
- Category: Member Galleries
-
Coopered Veneered Doors - anybody ever tried?
i'm tentatively planning on using hardwood core, cooper it, shape it, and then using shop-sawed veneer to go over both front and back. i have a small vac bag and i'm itching to use it on a curved form. so if this sounds like a lot of trouble, it is and i'm fine with it. i'm not looking to be...- BKHam
- Thread
- cooper coopering curved door veneer veneering
- Replies: 2
- Forum: General Woodworking
-
N
Veneer glue for humidor?
Hey, everybody. I am making a small, desktop humidor. The sides are made of spanish cedar and the top MDF. I am adding rosewood veneer on the outside. I was looking at titebond for veneer, but in the product specs it says not appropriate for high humidity. What glue should i use? Thanks, Jeff- N00B
- Thread
- glue humidity humidor titebond veneer
- Replies: 1
- Forum: General Woodworking
-
Geometric Table Top
- AL Spicer
- Media item
- design geometric table veneer
- Comments: 0
- Album: AL's photos
-
Geometric Table Front
- AL Spicer
- Media item
- design geometric table veneer
- Comments: 0
- Album: AL's photos
-
J
How to veneer square table legs?
I'd like to build 3"x3" square table legs using 8/4 walnut. I'm thinking I could glue two boards (2x3 each) together and then veneer each side using 1/8" veneer cut from the same board. If I go this route, do I miter the edges of the veneer to hide the seam? Can I chamfer the edges afterward or...- Jacaruso
- Thread
- veneer
- Replies: 12
- Forum: General Woodworking
-
M
Extra Thick Veneer and stringing for Federal Period Inlay Fans
During the workshop at Bill Clemmons' place in Liberty, NC, we made some Federal style fans like the one pictured. Several people were interested in buying some of the thick veneer and stringing for making these and requested I try to get some in small quantities, and list it for sale on my...- Matt Furjanic
- Thread
- inlay stringing veneer
- Replies: 5
- Forum: Where Can I Find, Buy or Sell?
-
Koa veneer picture frames
Koa veneer on cherry. BLO then several coats of amber shellac. Edges finished with black water based stain.- aamak
- Media item
- frame koa picture veneer
- Comments: 0
- Category: Smaller Woodworking Projects
-
My 1st cabinet
Dovetails and my own "brand" :-)- Jeremy Scuteri
- Media item
- cabinet dovetails drawers veneer
- Comments: 0
- Album: Cabinet
-
My 1st cabinet
Shop made veneer. This was my first time making my own veneer and my first time using veneer of any kind.- Jeremy Scuteri
- Media item
- cabinet dovetails drawers veneer
- Comments: 0
- Album: Cabinet
-
My 1st cabinet
Another view- Jeremy Scuteri
- Media item
- cabinet dovetails drawers veneer
- Comments: 0
- Album: Cabinet
-
My 1st cabinet
A lot of firsts on this project. First plywood box/cabinet, first time making drawers, first time making and using veneer, and first time making dovetails. Here it is after the finish.- Jeremy Scuteri
- Media item
- cabinet dovetails drawers veneer
- Comments: 0
- Album: Cabinet
-
My 1st cabinet
Assembly- Jeremy Scuteri
- Media item
- cabinet dovetails drawers veneer
- Comments: 0
- Album: Cabinet
-
My 1st cabinet
Dadoes and rabbets- Jeremy Scuteri
- Media item
- cabinet dovetails drawers veneer
- Comments: 0
- Album: Cabinet
-
My 1st cabinet
Plywood cut to size.- Jeremy Scuteri
- Media item
- cabinet dovetails drawers veneer
- Comments: 0
- Album: Cabinet
-
W
Burl veneer
Hi All, I am looking for smaller pieces / scraps of burl (or other interesting) veneer ranging in thicker depths. As small as 1 inch sq, but larger is welcome. I am new to learning about veneer, but the Mappa burl for one, is of interest. I'm near Charlotte. T I A, Jenna- woodwind
- Thread
- burl veneer
- Replies: 9
- Forum: Where Can I Find, Buy or Sell?
Premier Sponsor
Our Sponsors
LATEST FOR SALE LISTINGS
-
SOLD -- $75: Gast moa v113 Vacuum Pump Veneer, 60" bag and board- Started by peterdnight
- Replies: 1
-
GONE: Gladiator 5 cleats, 10 hangers, Paper Towel and Shelf
- Started by peterdnight
- Replies: 3
-
SOLD -- $100 Makita mac700 portable air + grex pin nailer + 2 others + 50' hose
- Started by peterdnight
- Replies: 1
-
-
