setup

  1. jonnyfontaine

    Setting drift on a Laguna 14/12

    Does anyone have any experience setting drift on a Laguna 14/12 bandsaw? Any advice you could help me with, thanks. Jonny
  2. jobelenus

    setting up grizzly 500 jointer

    I recently bought up a used 8" jointer - when I checked it out I ran a few boards through it and it seemed OK - didn't do the recommended straightedge...Lo and behold the beds are off - I took off the out feed table and tried to shim it up just a touch (according to the straightedge it was...
  3. Jointer setup workshop

    Jointer setup workshop

    • Bas
    • Media item
    • jointer setup workshop
    • Comments: 0
    • Album: NCWW folks
  4. Jointer setup workshop

    Jointer setup workshop

    • Bas
    • Media item
    • jointer setup workshop
    • Comments: 0
    • Album: NCWW folks
  5. Jointer setup workshop

    Jointer setup workshop

    • Bas
    • Media item
    • jointer setup workshop
    • Comments: 0
    • Album: NCWW folks
  6. Jointer setup workshop

    Jointer setup workshop

    • Bas
    • Media item
    • jointer setup workshop
    • Comments: 0
    • Album: NCWW folks
  7. Jointer setup workshop

    Jointer setup workshop

    • Bas
    • Media item
    • jointer setup workshop
    • Comments: 0
    • Album: NCWW folks
  8. Jointer setup workshop

    Jointer setup workshop

    • Bas
    • Media item
    • jointer setup workshop
    • Comments: 0
    • Album: NCWW folks
  9. Jointer setup workshop

    Jointer setup workshop

    • Bas
    • Media item
    • jointer setup workshop
    • Comments: 0
    • Album: NCWW folks
  10. Jointer setup workshop

    Jointer setup workshop

    • Bas
    • Media item
    • jointer setup workshop
    • Comments: 0
    • Album: NCWW folks
  11. Jointer setup workshop

    Jointer setup workshop

    • Bas
    • Media item
    • jointer setup workshop
    • Comments: 0
    • Album: NCWW folks
  12. Jointer setup workshop

    Jointer setup workshop

    • Bas
    • Media item
    • jointer setup workshop
    • Comments: 0
    • Album: NCWW folks
  13. ScottM

    Spraying setup?

    I am looking for my first spray setup. As most of you know most of my work is on small projects so I am not looking for a major production setup. Currently I use a lot of rattle can products like Deft. I am thinking lacquer as it dries very fast but I am open. I do not have a spray booth.
  14. MarkE

    Oneida DC setup on CL

    Might be a decent deal if there is enough duct and fittings, etc. http://raleigh.craigslist.org/tls/2634772765.html Oneida 3HP Cyclone Dust Collection System - $2000 (Holly Springs) Date: 2011-10-05, 8:15PM EDT Reply to: sale-egbqc-2634772765@craigslist.org [Errors when replying to ads?]...
  15. W

    Dust Collector setup ideas needed!

    Getting to the point where I need to add some DC to my work area. I've been using my shop vac connected to the port for my table saw and nothing on the blade guard. But as you know that doesn't work too well, still lots of dust all over the place. My space is small (12x24) and is shared as...
  16. kooshball

    Which plane or plane setup is best to trim tails and pins on through dovetails?

    I finished the top box for my dovetailed bookcase out of rswo and now need to trim the excess tail and pin material. Which plane is going to give me the best results on the end grain of this hard lumber? I have a jack plane, a fore plane and a low angle block plane at my disposal... Thanks
  17. T

    Who wanted a Leigh FMT setup?

    Someone from this forum emailed me a while ago wanting a Leigh FMT setup.(not the super FMT) I am sure that saved that email but in the sea of emails that I get I can't find it! If that was you, email me at thintz@newwoodworker.com
  18. kooshball

    How best to setup an old Stanley Bailey no. 6?

    I just cleaned up (clean enough to use, not clean enough to display) an old Stanley Bailey no. 6 plane and plan to replace the stock iron which is in bad shape with a Hock. The question is: should this type of a plane iron be ground with a crown or left essentially square? In case it helps, I...
  19. PChristy

    WorkSharp setup in the shop

    For theones that have the WorkSharp 3000 in their shops do you have a specific place for them with a nice setup or just sitting wherever you can find a place - if you have a nice setup could you post a picture of it I am trying to figure out where I would like to have mine in the shop - thanks
  20. kooshball

    very clever DC setup on sawmillcreek (link included)

    Found this today and thought it was quite interesting; especially the mount location for those of us working in garage. http://www.sawmillcreek.org/showthread.php?166826-Hybrid-Thien-McCallister-Dust-Collector-Project

Premier Sponsor

Our Sponsors

LATEST FOR SALE LISTINGS

Top