reducer

  1. T

    6" & 4" spiral pipe and fittings

    I am looking for approximately 60-80' of 6" spiral pipe and approximately 40' of 4" spiral pipe to help finish assembling my dust collection system. In addition, I will need 6x6x4" lateral y's. If you know of anyone that has some of these products would you please send them my way via email...
    • Temp626
    • Thread
    • collection collector cyclone duct ductwork dust fittings hose lateral pipe piping reducer separator shopvac spiral vacuum
    • Replies: 2
    • Forum: Where Can I Find, Buy or Sell?
  2. A

    In need of a used Shopsmith Speed Reducer

    I'm looking for a used shopsmith speed reducer for a mark V. I am in the middle of a project that I need to turn a large block and need to get the speed as low as possible for safety and ease. By speed reducer I am referring to the attachment that reduces the shopsmith's rpm by a factor of...
  3. S

    ShopSmith Owners: Anyone have the speed reducer?

    I was wondering if any ShopSmith owners here have the speed reducer? I attempted to turn a huge piece of wood a couple months ago, and it was definitely too out of balance for the lowest speed. It's a bit pricey for me with my current level of interest in turning, but wanted to get some...
  4. RandyJ

    How can I make this flooring reducer?

    OK all you woodworking gurus...HELP! I have a 1x3 piece of oak 6ft. long that will be trimmed to about 2 1/4" wide. I need to make a reducer similar to this one: Even as WW challenged as I am, I can cut the groove.:saw: What I need to know is how to easily create the large radius on the top...
  5. Flooring Reducer

    Flooring Reducer

    Flooring Reducer
    • RandyJ
    • Media item
    • flooring reducer
    • Comments: 0
    • Album: Misc
  6. Stock 'Y' Adapter

    Stock 'Y' Adapter

    Delta 50-769 Stock 'Y' Adapter.
    • KC7CN
    • Media item
    • 4" 5" 50-760 delta reducer to
    • Comments: 0
    • Album: Delta 50-760 Reducer
  7. Reducer Installed

    Reducer Installed

    The brace shown near the bottom of the picture prevents a 30 gallon trashcan from being centered under the DC input port.
    • KC7CN
    • Media item
    • 4" 5" 50-760 delta reducer to
    • Comments: 0
    • Album: Delta 50-760 Reducer
  8. Reducer Installed

    Reducer Installed

    Delta 50-760 shop-made reducer installed. A nice fit, and it works good. Unfortunately, not good enough for the intended use.
    • KC7CN
    • Media item
    • 4" 5" 50-760 delta reducer to
    • Comments: 0
    • Album: Delta 50-760 Reducer
  9. Delta 50-760 5" to 4" Reducer

    Delta 50-760 5" to 4" Reducer

    The Black part of reducer is a modified Delta 5'' inside, to 4'' outside reducer. The 5'' part was cut off, and the 4'' end was shortened. The transparent 5'' part is made from 1/4'' plastic rings. The diameter of each ring is slightly smaller than the next in order to insure a tight fit. To...
    • KC7CN
    • Media item
    • 4" 5" 50-760 delta reducer to
    • Comments: 0
    • Album: Delta 50-760 Reducer
  10. Delta 50-760 5" to 4" Reducer

    Delta 50-760 5" to 4" Reducer

    Shop-Made low-profile reducer. Failed attempt to connect pre-separator located under the blower motor.
    • KC7CN
    • Media item
    • 4" 5" 50-760 delta reducer to
    • Comments: 0
    • Album: Delta 50-760 Reducer
  11. T

    Find 7" to 6" dia. reducer for dust collector?

    I am looking for a 7" to 6" reducer for cyclone dust collector. The plumbing houses that I have checked do not carry them. Grizzly has an option but it is $58 when you buy the adapter and reducer. Seems very high to reduce a pipe diameter. :roll:

Premier Sponsor

Our Sponsors

LATEST FOR SALE LISTINGS

Top