presents

  1. B

    Ice Scraper Christmas presents

    Here’s a gift idea that works well for people living in the icy windshield prone areas. The 19” long handle makes it easy for short people to reach over the SUV hoods of today. The wood is 7/8” thick, 5” wide and 19” long. The bandsaw kerf is from a coarse-toothed .025” thick blade. The...
  2. PeteM

    A few Christmas presents . . .

    I copied the Chinese characters are from a book on the I Ching. They stand for Happiness, Family and Creativity. I carved the small bowl from a scrap of Claro Walnut I got from Kyle some time ago. And the cutting board (24" x 13" as requested) is from some left over maple. Now I have to work...
  3. J

    Looking to buy some Christmas Presents

    I'm looking for a couple of hand crafted Christmas Presents: Wine Stopper for around $25 Pen/ Pencil Set for around $35 Looking for something that has nice wood figure/contrast. Thanks, John
  4. PeteM

    Christmas Presents

    I made a bunch of Band Saw Boxes but LOML packed them up before I took Pix :BangHead: Soooooo . . . . . . Here's a Bowl I dug out of some curly Redwood I got from Kyle: and a little walnut box. The top rotates on a pin. Fun to make! pete
  5. Bryan S

    Christmas Presents for the Missus

    Here are a couple of present for the LOML. On the left is a clock and tide clock for her home office. The right a weather station. Both are cherry finished with Deft spray lacquer. My original plan was to make one long piece including the 3 weather instruments and tide clock but, we have a tide...
  6. More Christmas Presents

    More Christmas Presents

    Some more presents
    • woodturnerdon
    • Media item
    • cedar christmas more presents
    • Comments: 0
    • Category: Turning Projects
  7. Christmas Presents

    Christmas Presents

    These are some Christmas presents I made for 2010.
    • woodturnerdon
    • Media item
    • christmas presents
    • Comments: 0
    • Category: Turning Projects
  8. Trent Mason

    Christmas presents (better late than never)

    Here are a few Christmas presents that I made this year. In total, 3 cutting boards (the first was end grain and not pictured), two pens, and a clock (not pictured yet). It was weird for me working on this many projects at once. Coupled with work being as busy as we've ever been and my...
  9. Bryan S

    Couple of Christmas Presents for my daughter

    My daughter mentioned a few weeks ago about wanting a cutting board and here's what I came up with. One is cherry with maple accent the other is maple with cherry accent rubbed down with mineral oil. The second one did not turn out with as much contrast as I thought it might but good enough. I...
  10. jsjordan

    Christmas Presents

    Well, the elves have been burning the midnight oil getting this project ready for delivery tonight. :eusa_danc It is a doll bed for my 6 year-old grandaughter Rachel and is sized (I hope) :eusa_pray to fit the American Girl doll she is getting from Santa. It was a fun project and is basically...
  11. gesiak

    Finally got the heater working and turned a few XMAS presents

    Well that last couple of week have been a bit cold up here (just outside of Chicago).... well for you folks in NC you'd say frigid. After several trips to the hardware store for some pipe, elbows I got the old garage heater replaced. The garage is a warm 65 degrees while the outside is under 25...
    • gesiak
    • Thread
    • finally heater presents turned working xmas
    • Replies: 6
    • Forum: Woodturning
  12. DavidF

    First Xmas presents from the dark side

    Some friends gave me some pieces of Iron wood they had cut down and abandoned in the woods. I had no idea it would look this good until I cut into it! I made them this pestle and morter as a xmas gift in exchange. Some of it was just a little "furry" to sand perfectly, but a coat of CA soon...
  13. ashley_phil

    Chris Mathes Presents - Charlotte Woodworkers

    I'm pleased to announce that NCWWer Chris Mathes will do a presentation on Pen Turning at this month's Charlotte Woodworkers Meeting. Hope to see some of you there. The meeting is TOmorrow April 15th. Information is below. When and where: The Charlotte Woodworkers Association monthly...
  14. Jay

    Christmas Presents

    I have had a hard time finding time to log on but I did get some shop time before Christmas to make a few gifts. A gift for my brother who should be retiring from the submarine service in a couple years. I mounted it in a shadow box for him. Thanks for looking constructive criticism...
  15. NCPete

    my Christmas presents to the relatives

    I am pretty happy with how these are turning out: (now let's see if I don't screw this up, after helping other people put pics in their posts?:oops:) works in progress, waiting on the clamps and glue... need more clamps. yellow and purple heart cooking up finished product:
  16. C

    Christmas Presents Done...well almost

    I have been working hard the past few days to complete Christmas projects - potpourri boxes. I just finished 5 of the potpourri boxes...4 lids left to scroll and finish. These are the same style boxes that DL made last year. I made them in padauk, zebrawood, and lacewood, finished in lacquer...

Premier Sponsor

Our Sponsors

LATEST FOR SALE LISTINGS

Top