jointer

  1. Jointer setup workshop

    Jointer setup workshop

    • Bas
    • Media item
    • jointer setup workshop
    • Comments: 0
    • Album: NCWW folks
  2. Jointer setup workshop

    Jointer setup workshop

    • Bas
    • Media item
    • jointer setup workshop
    • Comments: 0
    • Album: NCWW folks
  3. Jointer setup workshop

    Jointer setup workshop

    • Bas
    • Media item
    • jointer setup workshop
    • Comments: 0
    • Album: NCWW folks
  4. Jointer setup workshop

    Jointer setup workshop

    • Bas
    • Media item
    • jointer setup workshop
    • Comments: 0
    • Album: NCWW folks
  5. Jointer setup workshop

    Jointer setup workshop

    • Bas
    • Media item
    • jointer setup workshop
    • Comments: 0
    • Album: NCWW folks
  6. Grizzly Jointer

    Grizzly Jointer

    • KenOfCary
    • Media item
    • grizzly jointer
    • Comments: 0
    • Category: Member Galleries
  7. Grizzly Jointer

    Grizzly Jointer

    • KenOfCary
    • Media item
    • grizzly jointer
    • Comments: 0
    • Category: Member Galleries
  8. Grizzly Jointer

    Grizzly Jointer

    • KenOfCary
    • Media item
    • grizzly jointer
    • Comments: 0
    • Category: Member Galleries
  9. Grizzly Jointer

    Grizzly Jointer

    • KenOfCary
    • Media item
    • grizzly jointer
    • Comments: 0
    • Category: Member Galleries
  10. Grizzly Jointer

    Grizzly Jointer

    • KenOfCary
    • Media item
    • grizzly jointer
    • Comments: 0
    • Category: Member Galleries
  11. D

    Router Jointer jig

    Just got my copy of Ultimate Router Handbook from Woodsmith. I am thinking of building the Router Jointer jig setup, as I have no room in my garage to a real jointer. My question is has anyone tried a setup like this and with good results and 2 I have a spare Dewalt DW617 router I was going to...
  12. R

    8" Jointer assembly?

    This may seem like a silly :eek: question, but I am looking to upgrade from my 6" jointer to an 8". I have a basement shop and am trying to figure out how to assemble the jointer once in my shop. I am looking at a Grizzly GO656PX and an Oliver 4230. The Grizzly weights 435 lbs and the Oliver...
  13. W

    Problem with PC jointer

    I have a Porter Cable jointer. (I bought what I could afford at the time.) It has worked well for some time. I have noticed that when jointing board edges, I have started getting a slight curve in the results. I assume that the two tables are not parallel but cannot find a way to fix this. If...
  14. bluthart

    Delta JT360 6" Jointer for Sale

    I have a Delta JT360 for sale. It is a few years old, is like new and cuts perfectly. The blades are very sharp and it includes a 4" dust port. Absolutely no rust on the table and freshly waxed. Sold new for $375.00 at Lowes. I have it on Craigslist for $250 but will give it to a NCWW member...
  15. T

    Sharpening jointer knives

    Does anyone have any experience or information about sharpening jointer knives? I replaced the knives on my Powermatic 60B 8" jointer and would like to sharpen the old set to have in reserve. I have a machinist friend who will grind them, but I'm not sure if there is only one angle involved. It...
  16. S

    8" jointer (Y/A) on craigslist, $350

    .
  17. T

    Jointer alignment

    I understand that the infeed and outfeed tables on my Powermatic 60B 8" jointer must be coplanar, but how much tolerance is there. Try as I might I can't get them perfect - the far end of the infeed table is probably .020 or so lower than the end nearest the cutter head and the outfeed table. Is...
  18. PeteM

    Restored Yates 24" jointer

    You know you want this !!! (Not mine ;-) Before After Full info and photos here http://forums.delphiforums.com/burl/messages/?start=Start+Reading+%3E%3E pete
  19. M

    Another Delta Pro 6" Jointer

    As with other posters, I am not affiliated with this CL listing: http://raleigh.craigslist.org/tls/2754889748.html This is making me start to wonder if there is a problem with the Delta Pro 6" Jointer.:wconfused:
  20. newtonc

    Delta jointer on CL

    Not affiliated with this item or seller This looks like a great buy for $200 if it is all up to par. http://raleigh.craigslist.org/tls/2748195031.html

Premier Sponsor

Our Sponsors

LATEST FOR SALE LISTINGS

Top