joiner

  1. N

    Delta X joiner (CL)

    Not mine. http://charlotte.craigslist.org/tls/1580859313.html
  2. R

    Want first biscuit joiner

    Hello All; I've never had one, and am in the market for a good, all around biscuit joiner. I've found an article in the February, 2008 issue of "Woodworker's Journal" on page 74 called "How to choose a biscuit joiner". Does anyone know of any other tool review articles for these? I take most...
  3. Bas

    DeWalt biscuit joiner on CL

    Not mine. At $75, with the biscuit assortment, this looks like a great deal! http://raleigh.craigslist.org/tls/1383501015.html
  4. tjgreen

    Ral CL: Porter-Cable biscuit joiner

    Not mine (I would never sell mine): http://raleigh.craigslist.org/tls/982428294.html New they're ~$220. Looks like a number of other items from the same seller in Clayton.
  5. owen299

    Planer / Joiner Help Needed

    HELP... I have a couple of walnut boards that I plan on using for a coffee table but I need to get them surfaced and squared up glueing(?). My little 6 in jointer and small delta plainer just arn't up to the job . they are 12 in wide ,60 in long and 5/4 so there is some room to work. Shouldn't...
  6. ScottM

    Joiner on Raleigh CL

    Not a bad deal if someone is in need of a 6" joiner. http://raleigh.craigslist.org/tls/540333674.html
  7. smessick

    Biscuit Joiner Experience

    I am getting into making clocks with an octagonal face frame and it occurs to me that a biscuit joiner might be the way to go for the frame. I know absolutely nothing about biscuit joiners and am trying to learn. Anyone care to share their experience/opinion? Thanks. Stan Messick
  8. erasmussen

    biscuit joiner

    I am now have a biscuit joiner thanks to the generosity of yellofins:-) Many thanks Ron:icon_thum
  9. T

    Charlotte CL - 12" planer, 12" joiner

    There is a 12" Belsaw planer and a 12" craftsman joiner for $100 each, listed on the Charlotte CL (items in Mathews). I don't know anything about them, except it could possibly be a good deal even if they're older stuff, providing you have a way to move them...
  10. J

    Joiner Table Adjustments

    Hi All, I was given a 6" Central Machinery joiner and I am trying to get the 2 tables level to each other. When I put a straight edge to the 2 tables, the out feed table is fine, but the back of the in feed table (right before the cutter blades) has a gap that disappears as you get to the...
  11. Joe Scharle

    Harbor Freight Plate Joiner

    Well I did it again! I'm not a big fan of bisquits as a rule, but for holding the ends of large picture frames while glueing they're hard to beat. Recently, I built a frame that was so big it was hard to hold on the router table to cut the slots and I made one really long! Then I saw a plate...
  12. M

    Freud js102 biscuit joiner

    I bought one despite the magazine reviews. They say that the fence slips. I found out quickly that one can easily adjust the fence. Mine came from the factory with the horizontal overhang loose enough to slip with moderate pressure. This was because the tightening arm would interfere with some...
  13. Phil

    biscut joiner

    Thought you might be interested in another use for this tool. I am putting down a tile floor and needed to undercut all the caseing and jambs. with the biscuit joiner adjusted to cut 3/4 inch deep , it works great for this task. Phil

Premier Sponsor

Our Sponsors

LATEST FOR SALE LISTINGS

Top