bowl
-
Bowl Attempts
Practice Work Clockwise from left - after five tries!- efr
- Media item
- basic bowl woodturning
- Comments: 0
- Category: Member Galleries
-
Fluted Spalted Maple Bowl
18" diameter with 24 hand carved flutes and carved feet- cyclopentadiene
- Media item
- bowl fluted maple spalted
- Comments: 0
- Category: Turning - 2011 Calendar Contest
-
Maple Bowl
Spalted Maple 12" diameter 1/16" wall thickness with carved feet. 2009 NC State Fair Blue Ribbon Winner for Woodturning- cyclopentadiene
- Media item
- bowl maple spalted
- Comments: 0
- Category: Turning - 2011 Calendar Contest
-
Ambrosia Maple Bowl
Ambrosia Maple Bowl- Sandy Rose
- Media item
- bowl
- Comments: 0
- Category: Turning - 2011 Calendar Contest
-
Vessel Bowl
Vessel Style Bowl made from Ambrosia Maple- Sandy Rose
- Media item
- bowl vessel
- Comments: 0
- Category: Turning - 2011 Calendar Contest
-
Wide Bowl
Wide Bowl made from Hard Maple- Sandy Rose
- Media item
- bowl
- Comments: 0
- Category: Turning - 2011 Calendar Contest
-
Fat Bowl from Ambrosia Maple
Fat Bowl from Ambrosia Maple- Sandy Rose
- Media item
- bowl fat
- Comments: 0
- Category: Turning - 2011 Calendar Contest
-
Segmented Bowl??
It is in segments so I guess it is... Never went near a lathe... I cut rings with the scroll saw and glued them together. View image in gallery View image in gallery It came from a piece of wood Charlie gave me, NY Butternut.- dlrion
- Thread
- bowl segmented
- Replies: 7
- Forum: Scrollsaw Work
-
T
My First Burl Bowl
This is my first Burl I ever turned. I have been turning for a little over a year and finally felt up to the challenge of a beast of a bowl as this, I turned it very green, the branch was only down 3 weeks before I turned it. Got it down to 1/4" sides and 3/8" bottom. It is 9.5" diameterx 4"...- thisnobody
- Thread
- bowl burl finish natural edge voids
- Replies: 8
- Forum: Woodturning
-
Red Oak Burl Bowl
9.5" diameter x 4" tall burl bowl with lots of voids and challenges. Turned very green and still drying awaiting a finish- thisnobody
- Media item
- bowl burl edge natural oak red
- Comments: 0
- Category: Member Galleries
-
Bowl Turning Question
I am turning my first "deep" bowl. I have a JEt 1642 lathe. I can reverse the motor on this model. Is it ok to do this so I can work on the inside of the deeper part of the bowl AND thus have a better line of sight to the portion I am working? Is there a danger here? Anything I need to consider...- Douglas Robinson
- Thread
- bowl question turning
- Replies: 8
- Forum: Woodturning
-
Have a Kelton Bowl saver? Willing to loan?
I am looking into the Kelton Bowl Saver, but would love to try it out before buying. Anyone have one that would be willing to loan it out for a test spin?- NCTurner
- Thread
- bowl kelton loan saver
- Replies: 1
- Forum: Woodturning
-
Looking for thick Walnut bowl blanks
I'm in the process of turning some large salad bowls and I've finally exhausted my supply of thick-wide Walnut lumber. I need something about 4" thick by 10" to 14" wide. I know I'm asking for a tough one. PM if you have something available :icon_thum. Thanks!- woodArtz
- Thread
- blanks bowl thick walnut
- Replies: 5
- Forum: Where Can I Find, Buy or Sell?
-
Square edge bowl
Hi all I have been trying to turn one of these buggers for 2 years fianaly to day made it all the way through. Some small cuts on the knuckles but all in all Me and the bowl are ok.:banana: not sure of the wood but the finish is blo/mineral sprits. Thanks for looking Mark- Mark Stewart
- Thread
- bowl edge square
- Replies: 8
- Forum: Woodturning
-
Claro Walnut Winged Bowl 02
- Nate Davey
- Media item
- bowl winged
- Comments: 0
- Category: Member Galleries
-
Claro Walnut Winged Bowl
This is the bowl I made in my class with Bill Wallace. There is a very small pedestal on it to give the impression it is hovering above the table- Nate Davey
- Media item
- bowl winged
- Comments: 0
- Category: Member Galleries
-
N
Basic Bowl Turning with Bill Wallace.
Today, I took the Basic Bowl Turning class taught by Bill Wallace at the Raleigh Woodcraft . Excellent class for starting out. Bill is an outstanding instructor who speaks clearly and concisely and makes the whole experience fun. He covered wood structure, cutting basics, chisel selection...- Nate Davey
- Thread
- basic bill bowl turning wallace
- Replies: 8
- Forum: Woodturning
-
My 6th bowl..
Here is my 6th bowl that is from some spalted silver maple burl. I tried to mimic a poached egg. The base is English Walnut. The finish is minwax poly. This was the first bowl with my Easy rougher.. I really like that tool. I just finished my dogwood burl bowl(1st bowl) and made...- Kyle
- Thread
- 6th bowl
- Replies: 7
- Forum: Woodturning
Premier Sponsor
Our Sponsors
LATEST FOR SALE LISTINGS
-
-
Graco 395 FinishPro air assisted airless sprayer for sale
- Started by RobH
- Replies: 1
-
-
-