Search results

  1. R

    Tools for sale

    I would be interested in the woelverine sharpening system. Pleaase send PM
  2. R

    So they are called PAPR

    If you are going to buy a PAPR be sure that it is NIOSH approved. Then you know that if you wear it CORRECTLY you will be protected!! If you have a beard and want to be protected should not ware a tight fitting porduct as it it will not seal at the hairy part of the face. Again if you want...
  3. R

    Noden Adjust-a-bench legs $350

    Thanks!!
  4. R

    Noden Adjust-a-bench legs $350

    Thanks for the suggestion. I have deleted my number!!
  5. R

    Noden Adjust-a-bench legs $350

    I can come up that way on Saturday, can that work for you? Can you send me a list of all parts that are included in the sale. Winston Salem is able 4+ hours from where I live. I will also be retuning home on the following Saturday from Asheville. Are the two legs the same width? The picture...
  6. R

    Noden Adjust-a-bench legs $350

    Do you still have this for sale? If so I may be interested. I need to know your location. I am in south east NC close to the water and SC boarder. I am coming to Asheville this weekend and returning home the following weekend. Let me know your situation.
  7. R

    Anyone have the Powermatic 15 HH planer?

    I like it. It leaves a nic smooth surface. At this point I have not had to rotate the cutting carbide squares. If you want any specific information send me a message
  8. R

    Virtual Picnic - May16 4PM Sign up here

    I plan to be there. Runk
  9. R

    Living With Arthritis in the Hands

    Mike, I understand your pain. I do have arthritis just about everywhere that seems to move. A few years ago the difficulty became so bad that I had trouble holding on to things. I saw a specialist at the Mayo Clinic in Rochester, MN. The left hand was in real bad shape. The fix for me...
  10. R

    Anyone else interested in a Saw Sharpening Workshop?

    I am interested but I live at the coast. Four our five hour drive is not appealing.
  11. R

    Cross-country moving costs for ww equipment

    I I have moved my shop and the entire house hold goods from MN to Eastern NC. It took three trips in a rented Pensky truck. I don't think we had anything break. The machinery worked just like in MN when it was hooked up. I packed the truck and drove it. It can be done. At 70 I would not do...
  12. R

    Design Help Request

    You might want to look at grinding wheel safety. Shields used to protect the user from a wheel that breaks in use which sends pieces in all directions. Shields have to protect against the impact of the flying projectile. Mass is taken into consideration when doing the calculation. NIOSH will...
  13. R

    starting a guild in Eastern NC

    I am interested. I live in Supply and I think you must be about 3 hours from here not sure since i have not consulted a map. IF meetings can accommodate the travel time or there is cheap lodging then my engagement and interest would increase. My wife is a quilter and we have made trips up...
  14. R

    Best Glue for making a Cutting Board

    Thanks for all the input. I will be using the Titebond III.
  15. R

    Need advice on transporting bandsaw and drill press

    I have moved both types of machinery from KY to MN in a 1972 short bed pick-up with a topper. I disassembled the band saw from the stand and further took the stand apart. Placed the saw against the cab wall and blocked it so it could not move. I took the head off the drill press and also...
  16. R

    Best Glue for making a Cutting Board

    I need to make a cutting board for my daughter in Washington State. What is the best glue for making the cutting board? I will be making it from hard maple with some decorative walnut strips. Thanks.
    • Runk
    • Thread
    • Replies: 8
    • Forum: Wood
  17. R

    Air Filter - Not Fine Woodworking

    According to filtration theory, the most penetrating particle size is near 0.3 to 0.1microns in size. This is the particle sizes that penetrates deep into the lungs and it is the sub micron particles that present the greatest health issues deep in the lungs. A typical furnace filter is not...
  18. R

    I need a Good Shop Vacuum ???

    I have a couple of older Fein Turbo IIs models. Got them as the models design was changing. I like to outfit them to take a bag. They do a nice job and are relatively quiet. I like them. The issue that I have is attachments since the Fein attachments are expensive and old ones off of old...
  19. R

    Wilmington Lunch Gathering - Saturdays May 10 and May 24

    I HAVE CANCELLED THE LUNCH FOR SATURDAY MAY 24 AS EVERYONE HAS FAMILY THINGS TO DO ON WHAT LOOKS LIKE A BEAUTIFUL WEEKEND. HOPE YOU ARE ABLE TO GET OUT AND ENJOY IT. THANKS TO EVERYONE FOR GETTING A GOOD START FOR AN EMERGING GROUP. RUNK :eusa_danc
  20. R

    Wilmington Lunch Gathering - Saturdays May 10 and May 24

    Is there any interest in lunch this Saturday, May 24 same place same time??. John and I are planning to attend but if no one else is going to attend John and I will do something different. Please reply if you have an interest. Thanks. RUNK

Premier Sponsor

Our Sponsors

LATEST FOR SALE LISTINGS

Top