Search results

  1. J

    Help finding a interior passage door raised panel bit

    I just had three solid wood six panel doors installed in my hallway to replace hollow doors. I have a small (20 1/2" by 50" hollow door) door that is for a small linen closet that is above the 25" by 20" return for my heat pump. This is typical setup for houses build in the 80's. I would like...
  2. J

    Need Help on ideas for front porch repair

    Thanks Jim...I will check out your ideas at Blevins Lumber in Wilkesboro.
  3. J

    Need Help on ideas for front porch repair

    I'm looking into the PVC at Home Depot. Only thing is if there is not a store in Mt. Airy I would have to got to Statesville or Winston Salem. The Virus is to bad for me to take a chance. I live in the Elkin/Jonesville area and I am 68, my wife has bad COPD. May just have to wait till the virus...
  4. J

    Need Help on ideas for front porch repair

    I am open for suggestions on what material and method of repair. I airnailed the cedar on and now have to remove the nails. Terminix was here two days ago and told me to wait two days for safety after he sprayed before starting my cleanup of nails and cleaning the 2X10. The new material will...
  5. J

    Need Help on ideas for front porch repair

  6. J

    Need Help on ideas for front porch repair

  7. J

    Need Help on ideas for front porch repair

    You will need to zoom in as much as possible on the two pocket holes to see the ants and eggs. The hole on the right at the bottom of hole will show the ant the best.
  8. J

    Need Help on ideas for front porch repair

    I am going to attempt to attach some pics very shortly
  9. J

    Need Help on ideas for front porch repair

    Carpenter Ant damage.. Around 2008 we had a front porch with a roof built to replace the deck on the front of the house. The PVC handrails were white and roof support columns were painted white to match. The band around the outsude of the porch was treated 2X10 and I put cedar 1X7 boards on...
  10. J

    Overlay Drawer Alignment Problem..Please Help

    Thanks Sky....I tried that and it worked.
  11. J

    Overlay Drawer Alignment Problem..Please Help

    Hi Tim and Phil....Going to start over tomorrow trying to id the problem. I also use spacers and started at the top drawer. I also use spacers when I build the face frame to hold members in place when putting in the pocket hole screws. Phil..I checked the sq inside the case with a two ft sq...
  12. J

    Overlay Drawer Alignment Problem..Please Help

    I am having trouble getting my overlay drawer box to alien correct to the face frame. I have a box I built with dovetails. Everything is sq. regardless of how I check it. Corner to corner with tape rule. Two foot sq and 12" combination. Cabinet is sq checked by same method. I am using...
  13. J

    Need help Patching a hole

    This is not a wood working question, but this problem is keeping me from finishing up my bathroom cabs. I have a small leak around the pvc pipe from my house to septic tank. I have dug it out and located where the water is coming into the basement. My question is what do I use to fill the...
  14. J

    Pocket Hole Drilling Question

    Thanks for the replies.. What is the best way to attach face frames to cabinets made with plywood? With my next project I can hide the PH's but what is a method when they cant be hidden? I think that 90 % of pocket holes I have done was drilled with the grain putting face frames together. That...
  15. J

    Pocket Hole Drilling Question

    On my last project I started to get ragged edges around the hole. I tried different ways to drill the hole. Fast and pushing hard and drilling slow all gave the same poor results. I was using a Dewalt battery drill and thought rpm's could be the problem. Also I went and bought a new bit and...

Premier Sponsor

Our Sponsors

LATEST FOR SALE LISTINGS

Top