Search results

  1. shawn

    Woodmaster 725 drumsander

    Thanks for the replies. I've used stuff from some online suppliers on my 712. I've even used paper from HF. I was really impressed with the mirka. I'll give the klingspor a try. Sent from my moto z4 using Tapatalk
  2. shawn

    Woodmaster 725 drumsander

    I recently purchased the drum sander attachment for my woodmaster planer. It came with a roll of mirka 80 and 120 grit paper. I was impressed with the performance of the paper. What do you use and where do you buy it? I want to buy bulk rolls online. Sent from my moto z4 using Tapatalk
  3. shawn

    Suitability of Oak & poplar for end grain cutting boards?

    I've use red oak cutting boards for decades. If youre worried about bacteria, the CDC recommends 1 tablespoon of bleach to 1 quart of water for dis-infecting. I wash mine with warm soapy water and wipe excess water and let dry.
  4. shawn

    Popular Woodworking - Greene and Greene

    Big fan of Greene and Greene. There was a shop in Tucson that did G@G replicas out of mesquite with desert ironwood pegs. Beautiful work and the most comfortable chairs I’ve ever sat in!
  5. shawn

    New Bern Mid-Summer Lunch Bunch

    I’ll try to be there.
  6. Eucalyptus block end table

    Eucalyptus block end table

    Ebonising dye and verdigris copper accents
  7. Writing Desk

    Writing Desk

    Live edge Eucalyptus slab desk with wedge base
  8. shawn

    Need to have a couple of slabs surfaced

    there is a shop in New Bern that has a 36" Porter with 2 Shelix heads. 1 for flattening, 1 for thickness. It's an impressive machine. I think they are pretty reasonable as well. Precision Molding.
  9. shawn

    Cabinet pulls drilling guide

    Fastcap made a pretty good jig. I used it when I was an independent millwork installer. I found that jigs are at there best when you have a pile of drawer heads that are the same size. Even if you have 3 different drawer sizes, there must be enough to make it worth changing the jig. Otherwise...
  10. shawn

    Drilling holes into tile?

    You can buy carbide bits designed for tile at lowes or ace. They typically come in 1/4, 3/8, and 1/2 inch. They don't require a hammer drill but use a low rpm sow you don't burn the bit.
  11. shawn

    Can plywood be successfully butt glued?

    Try edge gluing a sample piece. I think you will be quite satisfied with the result.
  12. shawn

    Can plywood be successfully butt glued?

    I,ve edge glued fairly large pieces of ply without issue except getting a consistently flush surface. The thickness of ply can vary a little so you wind up burning through the veneer when sanding.
  13. shawn

    Japanese woodworking

    I love this! I have a copy of Japanese Woodworking and have attempted at least one of the joints. Definitely something to aspire to. I've been wanting to do a blind mitered dovetail for a buffet I have in mind. This video was very enlightening.
  14. shawn

    Recovery from mistakes

    True. Many design innovations come from mistakes. Also, they are only mistakes if you don't learn from them.
  15. shawn

    Oak trunks for sale

    16' length. Woodweb log volume and weight calculators
  16. shawn

    Oak trunks for sale

    36" log is around 980 bdft and nearly 4000#
  17. shawn

    Oak trunks for sale

    How much are you asking for the trees?
  18. shawn

    Blum drawers

    I believe you are referring to the notches in the drawer back at the bottom corners to allow the blum motion glides to pass through. I usually use a dado blade.
  19. shawn

    Cabinet material advice

    MDF and melamine are ok for boxes, just heavy to handle.
  20. shawn

    Cabinet material advice

    Pre-finished maple ply is great for cabinet boxes. Light weight and fairly durable. Saves a ton of time. White or maple melamine provides a very durable surface, but it's heavy. Finishing cabinet interiors is a drag! spend the time on the doors and drawer heads, trim etc.

Our Sponsors

LATEST FOR SALE LISTINGS

Top